Related Experiment Video

Updated: Jun 3, 2025

Generating Lap Joints Via Friction Stir Spot Welding on DP780 Steel
07:18

Generating Lap Joints Via Friction Stir Spot Welding on DP780 Steel

Published on: August 13, 2019

6.9K

The lightweight design of steel pistons for diesel engines based on thermo-mechanical characteristics

Yang Liu1, Jilin Lei2, Jikun Chen1

  • 1Yunnan Key Laboratory of Internal Combustion Engines, Kunming University of Science and Technology, Kunming City, 650500, People's Republic of China.

Scientific Reports
|January 9, 2025
PubMed

Keywords:
Diesel engineLightweightProgressive designSteel pistonTopology optimization

More Related Videos

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle14:57

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle

Published on: January 30, 2019

13.7K
Rapid Manufacturing of Thin Soft Pneumatic Actuators and Robots08:47

Rapid Manufacturing of Thin Soft Pneumatic Actuators and Robots

Published on: November 8, 2019

7.6K

Related Concept Videos

Otto and Diesel Cycle01:27

Otto and Diesel Cycle

An Otto engine is a four-stroke engine that uses a mixture of gasoline and air as the working fuel. The fuel is injected into the cylinder, and the piston is moved completely down so that the cylinder is at maximum volume. By moving the piston up, adiabatic compression takes place. The spark plug ignites the gasoline-air mixture, and the burning fuel adds heat to the system at a constant volume. The heated mixture expands adiabatically and gets further cooled by exhausting heat, and this cyclic...
1.4K
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution...
166
Mechanical Characteristics of Steel01:18

Mechanical Characteristics of Steel

The mechanical characteristics of steel are assessed through various tests that evaluate its strength, toughness, and flexibility. These tests include tension, torsion, impact, bending, and hardness assessments, each providing crucial information about steel's suitability for specific applications.
The tension test is fundamental for determining tensile strength. In this test, a steel specimen is stretched using a gripping device until it breaks. The data collected during this test are used...
393
Design of Transmission Shafts - Stress Analysis01:15

Design of Transmission Shafts - Stress Analysis

Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
309
Work Done in an Adiabatic Process01:20

Work Done in an Adiabatic Process

Consider the adiabatic compression of an ideal gas in the cylinder of an automobile diesel engine. The gasoline vapor is injected into the cylinder of an automobile engine when the piston is in its expanded position. The temperature, pressure, and volume of the resulting gas-air mixture are 20 °C, 1.00 x 105 N/m2, and 240 cm3 , respectively. The mixture is then compressed adiabatically to a volume of 40 cm3. Note that, in the actual operation of an automobile engine, the compression is not...
3.1K
Transmission Shafts: Problem Solving01:09

Transmission Shafts: Problem Solving

Designing a solid shaft that transmits power from a motor to a machine tool involves a series of calculations to ensure the shaft can withstand the stresses applied by bending moments and torques. First, calculate the torque exerted on the gear, considering the power transmitted by the shaft and its rotational speed. Following this, compute the tangential forces acting on the gears, which directly relate to the torque and the gear radius.
Next, use bending moment diagrams for the shaft to...
210