Related Experiment Video

Updated: Jun 3, 2025

Surrogate Model Development for Digital Experiments in Welding
09:17

Surrogate Model Development for Digital Experiments in Welding

Published on: March 28, 2025

694

Development of Application Customization Toolkit (ACT) for 3D Thermal Elastic-Plastic Welding Analysis

Jaeyong Lee1,2, Dong Hee Park3,4, Juhyeon Park2

  • 1Department of Naval Architecture, Republic of Korea Naval Academy, 88-1, Changwon 51704, Republic of Korea.

Materials (Basel, Switzerland)
|January 11, 2025
PubMed

Keywords:
3D thermal elastic-plastic weldingT-joint fillet weldingresidual stressultimate compressive strengthweldingwelding deformation

More Related Videos

Experimental Methods for Investigation of Shape Memory Based Elastocaloric Cooling Processes and Model Validation11:11

Experimental Methods for Investigation of Shape Memory Based Elastocaloric Cooling Processes and Model Validation

Published on: May 2, 2016

11.0K
Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes06:34

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

Published on: January 6, 2023

1.6K

Related Concept Videos

Thermal expansion and Thermal stress: Problem Solving01:27

Thermal expansion and Thermal stress: Problem Solving

San Francisco's Golden Gate Bridge is exposed to temperatures ranging from -15 °C to 40 °C. At its coldest, the main span of the bridge is 1275 m long. Assuming that the bridge is made entirely of steel, what is the change in its length between these temperatures?
To solve the problem, first, identify the known and unknown quantities. The initial length (L) of the bridge is 1275 m, the coefficient of linear expansion (α) for steel is 12 x 10-6/°C, and the change in...
1.1K
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
138
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
93
Three-Dimensional Analysis of Strain01:29

Three-Dimensional Analysis of Strain

Three-dimensional strain analysis is crucial for understanding how materials deform under stress, particularly in elastic, homogeneous materials. This method employs principal stress axes to simplify complex stress states into more understandable forms. Subjected to stress, a small cubic element within a material either expands or contracts along these axes, transforming into a rectangular parallelepiped. This transformation effectively illustrates the material's deformation. The principal...
203
Thermal Strain01:19

Thermal Strain

Thermal strain is a concept that arises when we consider how temperature changes affect structures. Unlike the conventional assumption that structures remain constant under load, real-world scenarios often involve temperature fluctuations that can significantly impact these structures. Consider a homogeneous rod with a uniform cross-section resting freely on a flat horizontal surface. If the rod's temperature increases, the rod elongates. This elongation is proportional to the temperature...
616
Thermal Stress01:09

Thermal Stress

If the temperature of an object is changed while it is prevented from expanding or contracting, the object is subjected to stress. The stress is compressive if the object expands in the absence of constraint and tensile if it contracts. This stress resulting from temperature change is known as thermal stress. It can be quite large and can cause damage. To avoid this stress, engineers may design components so they can expand and contract freely. For instance, on highways, gaps are deliberately...
2.4K