Related Experiment Video

Updated: May 31, 2025

Frugal Imaging Technique of Capillary Flow Through Three-Dimensional Polymeric Printing Powders
06:01

Frugal Imaging Technique of Capillary Flow Through Three-Dimensional Polymeric Printing Powders

Published on: October 4, 2022

1.2K

Effective bulk and mass densities of randomly distributed coated cylinders in fluid

Asma Sellami1, Hervé Franklin2, Anouar Njeh1

  • 1Faculté des Sciences de Sfax, Laboratoire de Physique des Matériaux, Sfax, Tunisia.

The Journal of the Acoustical Society of America
|January 22, 2025
PubMed

More Related Videos

Experimental Measurement of Settling Velocity of Spherical Particles in Unconfined and Confined Surfactant-based Shear Thinning Viscoelastic Fluids10:28

Experimental Measurement of Settling Velocity of Spherical Particles in Unconfined and Confined Surfactant-based Shear Thinning Viscoelastic Fluids

Published on: January 3, 2014

13.4K
An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

8.5K

Related Concept Videos

Bulk Density of Aggregate01:22

Bulk Density of Aggregate

Bulk density refers to the mass of aggregate particles that would fill a unit volume. The concept of bulk density originates from the inability to pack aggregate particles in a manner that completely eliminates void spaces. Hence, the term bulk refers to the volume that encompasses both the aggregates and the voids. This measurement is crucial when aggregates are batched by volume and is used to convert quantities by mass to volume.
Most natural mineral aggregates, like sand and gravel,...
400
Density00:56

Density

Density is an important characteristic of substances, crucial in determining whether an object sinks or floats in a fluid. Its SI unit is kg/m3, and its cgs unit is g/cm3. The density of an object helps in identifying its composition, and also reveals information about the phase of the matter and its substructure. The densities of liquids and solids are roughly comparable, consistent with the fact that their atoms are in close contact. However, gases have much lower densities than liquids and...
14.6K
Density, Specific Weight, Specific Gravity and Compressibility of Fluid01:27

Density, Specific Weight, Specific Gravity and Compressibility of Fluid

Density, specific weight, specific gravity, and compressibility are fundamental properties of fluids. Density is the mass per unit volume, characterizing the mass of a fluid system. It influences buoyancy, pressure, flow dynamics, viscosity, thermal conductivity, and sound propagation. For instance, in pipeline design, accurate density measurements ensure that the pipeline can handle the fluid's mass.
Specific weight represents the weight per unit volume and is calculated by multiplying...
225
Accelerating Fluids01:17

Accelerating Fluids

When a fluid is in constant acceleration, the pressure and buoyant force equations are modified. Suppose a beaker is placed in an elevator accelerating upward with a constant acceleration, a. In the beaker, assume there is a thin cylinder of height h with an infinitesimal cross-sectional area, ΔS.
The motion of the liquid within this infinitesimal cylinder is considered to obtain the pressure difference. Three vertical forces act on this liquid:
1.0K
Density and Archimedes' Principle01:05

Density and Archimedes' Principle

When a lump of clay is dropped into water, it sinks. But if the same lump of clay is molded into the shape of a boat, it starts to float. Because of its shape, the clay boat displaces more water than the lump and experiences a greater buoyant force, even though its mass is the same. The same holds true for steel ships. The average density of an object majorly determines if the object will float. If an object's average density is less than that of the surrounding fluid, it will float. The...
6.5K
Bulk Modulus01:21

Bulk Modulus

The bulk modulus is a scientific term used to describe a material's resistance to uniform compression. It is the proportionality constant that links a change in pressure to the resulting relative volume change.
281