Related Experiment Video

Updated: May 30, 2025

Measuring Light-Switching Behavior Using an Occupancy and Light Data Logger
05:50

Measuring Light-Switching Behavior Using an Occupancy and Light Data Logger

Published on: January 16, 2020

5.8K

An approach to energy conservation in lighting systems using luminaire-based sensor for automatic dimming

Chaiyan Jettanasen1, Surakit Thongsuk2, Chayanut Sottiyaphai1

  • 1School of Engineering, King Mongkut's Institute of Technology Ladkrabang, Bangkok, 10520, Thailand.

Scientific Reports
|January 26, 2025
PubMed

Keywords:
Automatic Lighting ControlDaylightingEnergy savingLighting

More Related Videos

Operation of Laboratory Photobioreactors with Online Growth Measurements and Customizable Light Regimes05:21

Operation of Laboratory Photobioreactors with Online Growth Measurements and Customizable Light Regimes

Published on: October 28, 2021

2.1K
Indoor Experimental Assessment of the Efficiency and Irradiance Spot of the Achromatic Doublet on Glass ADG Fresnel Lens for Concentrating Photovoltaics09:00

Indoor Experimental Assessment of the Efficiency and Irradiance Spot of the Achromatic Doublet on Glass ADG Fresnel Lens for Concentrating Photovoltaics

Published on: October 27, 2017

8.8K

Related Concept Videos

Electrical Energy01:10

Electrical Energy

Using electric appliances for a longer period of time consumes more electrical energy and results in a higher electric bill. The energy produced by the transfer of electrons from one point to another is known as electrical energy. If power is delivered at a constant rate, the electrical energy can be defined as the product of power used by the device for a period of time. The energy unit on electric bills is the kilowatt-hour, where one kilowatt-hour is equivalent to 3.6 × 106 joules.
1.2K
Time and frequency -Domain Interpretation of Phase-lag Control01:21

Time and frequency -Domain Interpretation of Phase-lag Control

Phase-lag controllers are widely used in control systems to improve stability and reduce steady-state errors. A dimmer switch controlling the brightness of a light bulb serves as a practical example of phase-lag control, gradually adjusting the bulb's brightness. Mathematically, phase-lag control or low-pass filtering is represented when the factor 'a' is less than 1.
Phase-lag controllers do not place a pole at zero, but instead influence the steady-state error by amplifying any...
82
Conservation of AC Power01:15

Conservation of AC Power

The principle of power preservation is applicable to both ac and dc circuits. This principle, when applied to AC power, asserts that the complex, real, and reactive powers produced by the source are equal to the total complex, real, and reactive powers absorbed by the loads. When two load impedances are connected in parallel to an ac source V, the complex power provided by the source can be calculated using the relation
324
Conservation of Energy: Application01:12

Conservation of Energy: Application

When solving problems using the energy conservation law, the object (system) to be studied should first be identified. Often, in applications of energy conservation, we study more than one body at the same time. Second, identify all forces acting on the object and determine whether each force doing work is conservative. If a non-conservative force (e.g., friction) is doing work, then mechanical energy is not conserved. The system must then be analyzed with non-conservative work. Third, for...
6.5K
Power Distribution in Three-phase and Single Phase Circuits01:17

Power Distribution in Three-phase and Single Phase Circuits

Power distribution within electrical circuits is a foundational aspect of residential and industrial energy systems. While single-phase power is common in residential settings, three-phase power is the standard for industrial environments with heavy machinery. Each system is different and has advantages, and it's crucial to understand the underlying principles of power distribution and material efficiency.
Single-Phase Power Distribution:
Single-phase circuits are typical in household...
289
Secondary Distribution01:25

Secondary Distribution

Secondary distribution systems provide electrical energy at the utilization voltage levels from distribution transformers to customer meters. Typical secondary voltages in the United States include 120/240 V for residential use, 208Y/120 V for residential and commercial use, and 480Y/277 V for industrial and high-rise commercial use.
In residential areas, 120/240 V single-phase, three-wire service is commonly used for lighting, outlets, and large appliances. Urban areas with high-density loads...
79