Related Experiment Video

Updated: May 24, 2025

The HoneyComb Paradigm for Research on Collective Human Behavior
06:48

The HoneyComb Paradigm for Research on Collective Human Behavior

Published on: January 19, 2019

9.3K

Periodic Event-Triggered Optimal Output Consensus of Heterogeneous Multiagent Systems Subject to Communication Delays

Tianyu Liu, Lu Liu

    IEEE Transactions on Cybernetics
    |March 3, 2025
    PubMed

    More Related Videos

    Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface11:54

    Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface

    Published on: May 8, 2021

    4.3K
    Experimental Investigation of the Hierarchical Control in DC Microgrids Using a Real-time Simulator06:04

    Experimental Investigation of the Hierarchical Control in DC Microgrids Using a Real-time Simulator

    Published on: February 14, 2025

    176

    Related Concept Videos

    Propagation of Uncertainty from Systematic Error01:10

    Propagation of Uncertainty from Systematic Error

    The atomic mass of an element varies due to the relative ratio of its isotopes. A sample's relative proportion of oxygen isotopes influences its average atomic mass. For instance, if we were to measure the atomic mass of oxygen from a sample, the mass would be a weighted average of the isotopic masses of oxygen in that sample. Since a single sample is not likely to perfectly reflect the true atomic mass of oxygen for all the molecules of oxygen on Earth, the mass we obtain from this...
    453
    Propagation of Uncertainty from Random Error00:59

    Propagation of Uncertainty from Random Error

    An experiment often consists of more than a single step. In this case, measurements at each step give rise to uncertainty. Because the measurements occur in successive steps, the uncertainty in one step necessarily contributes to that in the subsequent step. As we perform statistical analysis on these types of experiments, we must learn to account for the propagation of uncertainty from one step to the next. The propagation of uncertainty depends on the type of arithmetic operation performed on...
    621
    BIBO stability of continuous and discrete -time systems01:24

    BIBO stability of continuous and discrete -time systems

    System stability is a fundamental concept in signal processing, often assessed using convolution. For a system to be considered bounded-input bounded-output (BIBO) stable, any bounded input signal must produce a bounded output signal. A bounded input signal is one where the modulus does not exceed a certain constant at any point in time.
    To determine the BIBO stability, the convolution integral is utilized when a bounded continuous-time input is applied to a Linear Time-Invariant (LTI) system....
    321
    Multi-input and Multi-variable systems01:22

    Multi-input and Multi-variable systems

    Cruise control systems in cars are designed as multi-input systems to maintain a driver's desired speed while compensating for external disturbances such as changes in terrain. The block diagram for a cruise control system typically includes two main inputs: the desired speed set by the driver and any external disturbances, such as the incline of the road. By adjusting the engine throttle, the system maintains the vehicle's speed as close to the desired value as possible.
    In the absence...
    93
    Linear time-invariant Systems01:23

    Linear time-invariant Systems

    A system is linear if it displays the characteristics of homogeneity and additivity, together termed the superposition property. This principle is fundamental in all linear systems. Linear time-invariant (LTI) systems include systems with linear elements and constant parameters.
    The input-output behavior of an LTI system can be fully defined by its response to an impulsive excitation at its input. Once this impulse response is known, the system's reaction to any other input can be...
    202
    Distributed Loads: Problem Solving01:21

    Distributed Loads: Problem Solving

    Beams are structural elements commonly employed in engineering applications requiring different load-carrying capacities. The first step in analyzing a beam under a distributed load is to simplify the problem by dividing the load into smaller regions, which allows one to consider each region separately and calculate the magnitude of the equivalent resultant load acting on each portion of the beam. The magnitude of the equivalent resultant load for each region can be determined by calculating...
    610