Related Experiment Video

Updated: May 24, 2025

Visualizing Hyporheic Flow Through Bedforms Using Dye Experiments and Simulation
09:49

Visualizing Hyporheic Flow Through Bedforms Using Dye Experiments and Simulation

Published on: November 18, 2015

12.1K

Numerical simulation of water exchange between the karst matrix and the adjacent conduit at the micro-scale

Jiao Li1, Douqiang Yang1, Guanping An1

  • 1School of Environmental Science and Engineering, Southwest Jiaotong University, Chengdu, 611756, Sichuan, China.

Scientific Reports
|March 6, 2025
PubMed

Keywords:
Digital core technologyKarst water-bearing mediaMatrix–conduit exchangeNumerical simulationStokes-Brinkman equation

More Related Videos

Wastewater Irrigation Impacts on Soil Hydraulic Conductivity: Coupled Field Sampling and Laboratory Determination of Saturated Hydraulic Conductivity08:09

Wastewater Irrigation Impacts on Soil Hydraulic Conductivity: Coupled Field Sampling and Laboratory Determination of Saturated Hydraulic Conductivity

Published on: August 19, 2018

9.1K
A Microfluidic Platform to Study Bioclogging in Porous Media05:10

A Microfluidic Platform to Study Bioclogging in Porous Media

Published on: October 13, 2022

1.8K

Related Concept Videos

Typical Model Studies01:30

Typical Model Studies

Fluid mechanics model studies often utilize scaled-down systems to predict fluid behavior in full-scale environments, such as river flows, dam spillways, and structures interacting with open surfaces. Maintaining Froude number similarity in river models is crucial, as it replicates surface flow features like wave patterns and velocities.
292
Design Example: Creating a Hydraulic Model of a Dam Spillway01:21

Design Example: Creating a Hydraulic Model of a Dam Spillway

Scaled hydraulic models of dam spillways provide a practical way to replicate and study the intricate flow dynamics of these structures. Often built to a 1:15 ratio, these models allow for observing critical water behavior, such as velocity distribution, flow patterns, and energy dissipation.
114
Design Example: Design of an Irrigation Channel01:27

Design Example: Design of an Irrigation Channel

Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
54
Uniform Depth Channel Flow: Problem Solving01:18

Uniform Depth Channel Flow: Problem Solving

To calculate the flow rate for a trapezoidal channel, first, identify the bottom width, side slope, and flow depth of the channel. The cross-sectional area (A) corresponding to the depth of flow (y), channel bottom width (B), and side slope (θ) is determined by:Next, calculate the wetted perimeter, which includes the bottom width and the sloped side lengths in contact with the water. Using the values of the cross-sectional area and the wetted perimeter, determine the hydraulic radius by...
48
Rapidly Varying Flow01:24

Rapidly Varying Flow

Rapidly varying flow (RVF) in open channels is characterized by abrupt changes in flow depth over a short distance, with the rate of depth change relative to distance often approaching unity. These flows are inherently complex due to their transient and multi-dimensional nature, making exact analysis difficult. However, approximate solutions using simplified models provide valuable insights into their behavior.Key Features of Rapidly Varying FlowRVF is commonly observed in scenarios involving...
43
Continuity Equation01:28

Continuity Equation

The continuity equation asserts that the mass flow rate must remain constant for a steady flow of an incompressible fluid within a confined system. This principle applies to systems where fluid passes through varying cross-sectional areas, such as nozzles, syringes, and pipes.
The mass flow rate is expressed as:
954