Related Experiment Video

Updated: Oct 3, 2026

Generating Lap Joints Via Friction Stir Spot Welding on DP780 Steel
07:18

Generating Lap Joints Via Friction Stir Spot Welding on DP780 Steel

Published on: August 13, 2019

Mortality of welders and other craftsmen at a shipyard in NE England

M L Newhouse, D Oakes, A J Woolley

    British Journal of Industrial Medicine
    |June 1, 1985
    PubMed

    More Related Videos

    Surrogate Model Development for Digital Experiments in Welding09:17

    Surrogate Model Development for Digital Experiments in Welding

    Published on: March 28, 2025

    Automatic Laser-based Geometry Capture for Finite Element Analysis of Weld Beads07:58

    Automatic Laser-based Geometry Capture for Finite Element Analysis of Weld Beads

    Published on: July 25, 2025

    Related Concept Videos

    Fatigue01:21

    Fatigue

    Fatigue occurs when materials rupture under repeated or fluctuating loads, even at stress levels far below their static breaking strength. It typically results in brittle failure, even for ductile materials. It is a critical consideration in designing machines and structural components subjected to repetitive or varying loads. The nature of these loadings can range from fluctuating loads like unbalanced pump impellers causing vibrations to repeatedly bending a thin steel rod wire back and forth...
    Residual Stresses01:26

    Residual Stresses

    Residual stresses reside in a structure even after removing the original stress inducer. This phenomenon often arises from varied plastic deformations across different parts of a structure. Consider a rod stretched beyond its yield point. It will not regain its original length due to permanent deformation. Even after load removal, the rod does not entirely lose stress because of uneven plastic deformations, resulting in residual stresses. The computation of these stresses in structures is...
    Yield Criteria for Ductile Materials under Plane Stress01:25

    Yield Criteria for Ductile Materials under Plane Stress

    In designing structural elements and machine parts using ductile materials, it is crucial to ensure that these components withstand applied stresses without yielding. Yielding is initially determined through a tensile test, which evaluates the material's response to uniaxial stress. However, tensile stress is insufficient when components face biaxial or plane stress conditions This condition requires advanced criteria to predict failure.
    The Maximum Shearing Stress Criterion, also known as the...
    Brick Masonry01:12

    Brick Masonry

    Brick masonry uses bricks as the building blocks and involves building walls from individual bricks laid in mortar. The basic building block of brick masonry is the wythe, a vertical layer of bricks with a thickness of one brick. Within a wythe, bricks can be laid in various courses or patterns, with the most common being the stretcher course, where bricks are laid with their long edge horizontal and face parallel to the wall.
    For thicker walls, multiple wythes are bonded together using...
    Steel Manufacturing01:26

    Steel Manufacturing

    Steel manufacturing is a multi-stage process that begins by smelting iron ore into cast iron in a blast furnace. This initial stage involves layering iron ore with coke, a type of fuel, and crushed limestone within the furnace. The coke is ignited with a high volume of air, leading to the creation of carbon monoxide, which acts to reduce the iron ore to pure iron.
    During this smelting process, limestone plays a crucial role by forming slag. Slag captures impurities within the molten iron, such...
    Steel Fastening Techniques01:17

    Steel Fastening Techniques

    Steel sections can be joined together through various fastening techniques including riveting, bolting, and welding, each suitable for different structural requirements and conditions.
    Rivets are cylindrical steel fasteners with a specially designed head. During application, rivets are heated until white-hot and then inserted through pre-drilled holes in the steel sections. A pneumatic hammer is used to shape the exposed end into a second head, securing the sections together.
    Bolting is another...