Related Experiment Video

Updated: May 23, 2025

A Uniaxial Compression Experiment with CO2-Bearing Coal Using a Visualized and Constant-Volume Gas-Solid Coupling Test System
10:27

A Uniaxial Compression Experiment with CO2-Bearing Coal Using a Visualized and Constant-Volume Gas-Solid Coupling Test System

Published on: June 12, 2019

8.6K

The study on the adsorption characteristics of anthracite under different temperature and pressure conditions

Danan Zhao1, Xiaofei Ke1, Mincong Huang1

  • 1Faculty of Civil Engineering and Architecture, Zhanjiang University of Science and Technology, Zhanjiang, Guangdong, China.

Plos One
|March 11, 2025
PubMed

More Related Videos

Experimental Study of the Relationship Between Particle Size and Methane Sorption Capacity in Shale07:23

Experimental Study of the Relationship Between Particle Size and Methane Sorption Capacity in Shale

Published on: August 2, 2018

7.5K
Adsorption Device Based on a Langatate Crystal Microbalance for High Temperature High Pressure Gas Adsorption in Zeolite H-ZSM-509:46

Adsorption Device Based on a Langatate Crystal Microbalance for High Temperature High Pressure Gas Adsorption in Zeolite H-ZSM-5

Published on: August 25, 2016

11.5K

Related Concept Videos

Pressure and Volume in an Adiabatic Process01:27

Pressure and Volume in an Adiabatic Process

Free expansion of a gas is an adiabatic process. However, there are few differences between free expansion and adiabatic expansion. During free expansion, no work is done, and there is no change in internal energy. But, for an adiabatic expansion, work is done, and there is a change in internal energy. During an adiabatic process, the relation between the pressure and volume is obtained from the condition for the adiabatic process, that is, 
2.6K
Work Done in an Adiabatic Process01:20

Work Done in an Adiabatic Process

Consider the adiabatic compression of an ideal gas in the cylinder of an automobile diesel engine. The gasoline vapor is injected into the cylinder of an automobile engine when the piston is in its expanded position. The temperature, pressure, and volume of the resulting gas-air mixture are 20 °C, 1.00 x 105 N/m2, and 240 cm3 , respectively. The mixture is then compressed adiabatically to a volume of 40 cm3. Note that, in the actual operation of an automobile engine, the compression is not...
3.1K
Adiabatic Processes for an Ideal Gas01:18

Adiabatic Processes for an Ideal Gas

When an ideal gas is compressed adiabatically, that is, without adding heat, work is done on it, and its temperature increases. In an adiabatic expansion, the gas does work, and its temperature drops. Adiabatic compressions actually occur in the cylinders of a car, where the compressions of the gas-air mixture take place so quickly that there is no time for the mixture to exchange heat with its environment. Nevertheless, because work is done on the mixture during the compression, its...
3.0K
Phase Diagram01:19

Phase Diagram

The phase of a given substance depends on the pressure and temperature. Thus, plots of pressure versus temperature showing the phase in each region provide considerable insights into the thermal properties of substances. Such plots are known as phase diagrams. For instance, in the phase diagram for water (Figure 1), the solid curve boundaries between the phases indicate phase transitions (i.e., temperatures and pressures at which the phases coexist).
5.7K
Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...
39.3K