Related Experiment Video

Updated: May 21, 2025

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes
06:34

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

Published on: January 6, 2023

1.6K

A novel foldable metamaterial for application in the pipeline pressure vessel with a static deformation, strain and

Xu Ying1, An Yunzhu2, Ye Qige1

  • 1Guangzhou Electric Power Design Institute Co., Ltd, Guangzhou, 510000, China.

Scientific Reports
|March 21, 2025
PubMed

Keywords:
Deformable modelFoldable metamaterialsNanofillersPipeline vesselsThermal and mechanical loads

More Related Videos

Characterizing Dissipative Elastic Metamaterials Produced by Additive Manufacturing09:39

Characterizing Dissipative Elastic Metamaterials Produced by Additive Manufacturing

Published on: June 28, 2024

798
Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes06:56

Micro/Nano-scale Strain Distribution Measurement from Sampling Moiré Fringes

Published on: May 23, 2017

12.2K

Related Concept Videos

Three-Dimensional Analysis of Strain01:29

Three-Dimensional Analysis of Strain

Three-dimensional strain analysis is crucial for understanding how materials deform under stress, particularly in elastic, homogeneous materials. This method employs principal stress axes to simplify complex stress states into more understandable forms. Subjected to stress, a small cubic element within a material either expands or contracts along these axes, transforming into a rectangular parallelepiped. This transformation effectively illustrates the material's deformation. The principal...
188
Bending of Material: Problem Solving01:09

Bending of Material: Problem Solving

In this lesson, determine the ratio of the maximum bending moments applied to two metal pipes, given that both pipes can withstand a maximum stress of 100 MPa. Both pipes have an outer radius of 1.8 cm. Pipe A has an inner radius of 1.5 cm, and Pipe B has an inner radius of 1 cm. The ratio of the maximum bending moment applied to two metallic pipes, each with a different inner and outer radius, is determined by considering their dimensions. The inner radius of the first pipe is 1.5 cm, and for...
168
Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
137
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
134
Plastic Deformations of Members with a Single Plane of Symmetry01:21

Plastic Deformations of Members with a Single Plane of Symmetry

When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
85
Transformation of Plane Stress01:18

Transformation of Plane Stress

Studying stress transformation is essential in understanding how stress components within a material, like a cube under plane stress, change with rotation. This change is analyzed by considering a prismatic element within the cube. As the element rotates, the stress components acting on it—both normal and shearing stresses—change in magnitude and orientation. This change is quantified using trigonometric functions of the rotation angle, relating the forces acting on the rotated element's...
178