Related Experiment Video

Updated: May 12, 2026

Visualization of High Speed Liquid Jet Impaction on a Moving Surface
08:34

Visualization of High Speed Liquid Jet Impaction on a Moving Surface

Published on: April 17, 2015

Numerical Investigation of Effect of Nozzle Upper Divergent Angle on Asymmetric Rectangular Section Ejector

Manfei Lu1, Jingming Dong1, Chi Feng1

  • 1Institute of Marine Engineering and Thermal Science, Marine Engineering College, Dalian Maritime University, Dalian 116026, China.

Entropy (Basel, Switzerland)
|March 28, 2025
PubMed

Keywords:
asymmetric ejectormixing layernozzle divergent anglerectangular sectionshock wave

More Related Videos

Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel10:03

Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel

Published on: October 5, 2018

Cryogenic Liquid Jets for High Repetition Rate Discovery Science08:34

Cryogenic Liquid Jets for High Repetition Rate Discovery Science

Published on: May 9, 2020

Related Concept Videos

Bernoulli's Principle: Applications01:17

Bernoulli's Principle: Applications

There are many devices and situations in which fluid flows at a constant height and so can be analyzed using Bernoulli's principle. These devices include, but are not limited to, entrainment devices and fluid flow measuring devices.
Entrainment devices use a high fluid speed to create low pressures and, thus, entrain one fluid into another. Some examples of these devices are given below:
Thin-Walled Hollow Shafts01:15

Thin-Walled Hollow Shafts

In analyzing a thin-walled hollow shaft subjected to torsional loading, a segment with width dx is isolated for examination. Despite its equilibrium state, this segment faces torsional shearing forces at its ends. These forces are quantitatively described by the product of the longitudinal shearing stress on the segment's minor surface and the area of this surface, leading to the concept of shear flow. This shear flow is consistent throughout the structure, indicating a uniform distribution of...
Bernoulli's Equation for Flow Normal to a Streamline01:16

Bernoulli's Equation for Flow Normal to a Streamline

Bernoulli's equation for flow normal to a streamline explains how pressure varies across curved streamlines due to the outward centrifugal forces induced by the fluid's curvature. The pressure is higher on the inner side of the curve, near the center of curvature, and decreases outward to balance these centrifugal forces.
The pressure difference depends on the fluid's velocity and radius of curvature. The pressure variation is minimal in flows with nearly straight streamlines. However, the...
Free Jet01:14

Free Jet

Free jets describe the flow of liquid exiting a reservoir through an opening into the atmosphere without resistance. The velocity (v) of the liquid jet is derived using Bernoulli's principle and expressed as:
Design Example: Flow Through a Fire Extinguisher01:12

Design Example: Flow Through a Fire Extinguisher

A fire extinguisher that uses pressurized water relies on fluid dynamics principles to generate a high-velocity stream capable of suppressing flames. The water is stored at a much higher pressure inside the extinguisher than the surrounding atmosphere. This pressure difference forces the water to flow rapidly when the extinguisher is activated, and the behavior of the water as it exits the nozzle can be understood using fundamental equations of fluid dynamics.
The key to understanding how the...
Area of a Surface of Revolution01:29

Area of a Surface of Revolution

Surfaces of revolution are formed when a two-dimensional curve is rotated around an axis, producing a three-dimensional shape. This concept is used in engineering tasks like determining the surface area of a rocket nozzle, where precise calculations are critical for applying uniform heat-resistant coatings. When a curve is revolved about the x-axis, it sweeps out a continuous surface whose area must be calculated accurately to estimate material requirements.Approximating with Conical BandsTo...