Related Experiment Video

Updated: May 16, 2025

Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores
09:32

Mechanical Expansion of Steel Tubing as a Solution to Leaky Wellbores

Published on: November 20, 2014

12.1K

Application of CIPP flipped lining method in the rehabilitation of old gas pipelines

You Yun1, Wang Xinxin2, Wang Zhongyi1

  • 1School of Petroleum Engineering, Chongqing University of Science and Technology, Chongqing, 401331, China.

Scientific Reports
|April 1, 2025
PubMed

Keywords:
CIPP flipped liningConstructionOld gas pipelinesRepair techniquesTrenchless

More Related Videos

Visualization of Flow Field Around a Vibrating Pipeline Within an Equilibrium Scour Hole00:09

Visualization of Flow Field Around a Vibrating Pipeline Within an Equilibrium Scour Hole

Published on: August 26, 2019

5.5K
Sandy Soil Improvement through Microbially Induced Calcite Precipitation MICP by Immersion06:27

Sandy Soil Improvement through Microbially Induced Calcite Precipitation MICP by Immersion

Published on: September 12, 2019

9.3K

Related Concept Videos

Multiple Pipe Systems01:21

Multiple Pipe Systems

Multipipe systems consist of complex configurations of interconnected pipes designed to transport fluids efficiently across intricate networks. They are essential in engineering applications requiring precise control over flow distribution, pressure, and head loss. They are categorized into series, parallel, loop, and network configurations, each distinguished by unique flow characteristics and applications.
Series Configuration
In a series configuration, fluid flows sequentially from one pipe...
281
Pumped Concrete01:13

Pumped Concrete

Concrete in large quantities can be pumped across long distances for placing in inaccessible sites. This system comprises a hopper that receives concrete from a mixer, a pump to propel the concrete, and pipelines that facilitate its delivery.
For direct-acting pumps, the concrete enters the pump via the inlet valve under the action of gravity and suction created by the movement of the piston. This concrete is then forced into the pipeline and out through the outlet valve by the forward movement...
55
Preplaced Aggregate Concrete01:29

Preplaced Aggregate Concrete

Preplaced aggregate concrete is ideal for construction environments that are not easily accessible. The process begins by properly wetting the gap-graded coarse aggregates to remove the dirt, then placing it in the form and compacting it. Voids are filled with a mortar mix pumped under pressure through slotted pipes. This mortar typically consists of Portland cement, pozzolan, fine aggregates, water, and a fluidizing aid. The pozzolan helps reduce bleeding and segregation while improving the...
88
Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
71
Plane Potential Flows01:23

Plane Potential Flows

Plane potential flows simplify fluid motion by assuming the fluid to be irrotational and incompressible. These characteristics allow these flows to be described by a velocity potential function, ϕ, representing the flow speed in a given direction, and a stream function, ψ, that visualizes the flow path, both governed by Laplace's equation. These parameters help in estimating flow patterns, velocity distributions, and pressure fields around various hydraulic structures.
Uniform...
204
Curing Methods01:26

Curing Methods

Concrete members with a small surface-to-volume ratio are cured by oiling and moistening the forms before casting the concrete member. These forms can be left in place for a prolonged period to prevent moisture loss, and can be wetted if made of a material suitable for wetting. If the forms are removed early, the concrete member is moistened and covered with polythene sheets to maintain moisture. For large horizontal concrete surfaces exposed to dry weather, a temporary covering is suspended...
64