Related Experiment Video

Updated: Jul 15, 2026

Design, Fabrication, and Experimental Characterization of Plasmonic Photoconductive Terahertz Emitters
10:54

Design, Fabrication, and Experimental Characterization of Plasmonic Photoconductive Terahertz Emitters

Published on: July 8, 2013

14.9K

A simple independent triple-sideband THz signal generation and detection scheme based on delta-sigma modulation and

Zheng Hu, Yilin Chen, Xue Han

    Optics Letters
    |June 13, 2025
    PubMed

    More Related Videos

    Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators09:23

    Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators

    Published on: May 30, 2014

    14.5K
    Generation and Coherent Control of Pulsed Quantum Frequency Combs06:42

    Generation and Coherent Control of Pulsed Quantum Frequency Combs

    Published on: June 8, 2018

    8.9K

    Related Concept Videos

    ¹³C NMR: ¹H–¹³C Decoupling01:04

    ¹³C NMR: ¹H–¹³C Decoupling

    The probability of having two carbon-13 atoms next to each other is negligible because of the low natural abundance of carbon-13. Consequently, peak splitting due to carbon-carbon spin-spin coupling is not observed in spectra. However, protons up to three sigma bonds away split the carbon signal according to the n+1 rule, resulting in complicated spectra.
    A broadband decoupling technique is used to simplify these complex, sometimes overlapping, signals. Broadband decoupling relies on a...
    The Y-to-Delta Circuit01:19

    The Y-to-Delta Circuit

    A balanced wye-to-delta circuit comprises balanced Y-connected voltage sources and delta-connected loads with no neutral line connection.
    The initial step in analyzing a wye-to-delta circuit is to assume a positive phase sequence. These phase voltages are then utilized to calculate the line voltages that occur directly across the delta-connected load impedances. Van, Vbn, and Vcn are the phase voltages in wye, and Vab, Vbc, and Vca are the line voltages for a delta circuit. The relation between...
    The Delta-to-Delta Circuit01:17

    The Delta-to-Delta Circuit

    In a delta-delta configuration, the source and the load are connected in a delta manner, forming a closed loop that divides the network into three distinct phases. This configuration makes the phase voltages identical to line voltages. Assuming the sources are in positive sequence, the phase voltages can be expressed directly without having a neutral wire.
    The Delta-to-Y Circuit01:16

    The Delta-to-Y Circuit

    In the delta-wye circuit, the source is delta-connected, while the load is in a wye configuration. This means that the phase voltage of the delta-connected source is equal to the line voltage of the wye-connected load. The connection between two-line currents originates from the delta-connected source. The phase difference in the balanced system allows for calculating one line current given the other, utilizing the positive sequence of phases. In the delta-wye system, the phase currents in the...
    Basic Discrete Time Signals01:16

    Basic Discrete Time Signals

    The unit step sequence is defined as 1 for zero and positive values of the integer n. This sequence can be graphically displayed using a set of eight sample points, showing a step function starting from n=0 and remaining constant thereafter.
    The unit impulse or sample sequence is mathematically expressed as zero for all n values except at n=0, where it is one. The unit impulse sequence, denoted by δ(n), is the first difference of the unit step sequence, while the unit step sequence u(n) is the...
    Sampling Continuous Time Signal01:11

    Sampling Continuous Time Signal

    In signal processing, a continuous-time signal can be sampled using an impulse-train sampling technique, followed by the zero-order hold method. Impulse-train sampling involves the use of a periodic impulse train, which consists of a series of delta functions spaced at regular intervals determined by the sampling period. When a continuous-time signal is multiplied by this impulse train, it generates impulses with amplitudes corresponding to the signal's values at the sampling points.
    In the...