The relation of musculoskeletal disorders to ergonomic work demands in welders and electrical workers: a prospective Canadian cohort study

  • 0Division of Preventive Medicine, University of Alberta, Edmonton, AB T6G 2T4, Canada.
Annals of work exposures and health +

|

Abstract

INTRODUCTION

Musculoskeletal disorders are known to result from physical demands at the workplace. Identification of risks specific to particular trades may encourage work modification to prevent new onset conditions.

METHODS

In a Canadian cohort study of male and female welders and electrical workers, we collected self-reports of low-back pain, shoulder pain, and symptoms suggestive of vibration white finger (VWF) at each 6-monthly contact for up to 5 yr. Physician records of back and shoulder/joint disorders and Raynaud's syndrome were extracted from the Alberta administrative health database (AHDB). At each contact, participants completed questions on ergonomic work factors. We computed cumulative hours exposed for 6 factors: whole-body vibration, hand-arm vibration, manipulating heavy objects, working at or above shoulder height, working while crouching or kneeling, and work in cold environments. The relation of current and log cumulative exposures to health outcomes was identified by proportional hazards regression, adjusting for sex, age, body mass index, smoking, anxiety, and depression.

RESULTS

Of 1,885 workers recruited January 2011 to September 2017, 872 welders and 812 electrical workers recorded symptoms and workplace demands on at least one occasion, with 693 welders and 567 electrical workers matched to the AHDB. In final models, whole-body vibration was related overall to each self-reported health outcome with backpain risk most in evidence for male welders (HR = 1.10 log increase/h of exposure: 95% CI, 1.05 to 1.15, P < 0.001). Working in a crouching position and in cold temperatures also contributed to back pain in welders. Cumulative hours working at or above shoulder height increased welders' risk of shoulder pain (HR = 1.07 log increase/h of exposure: 95% CI, 1.03 to 1.11, P = 0.001). Working at or above shoulder height was related to both back and shoulder pain in the electrical trades, where cumulative exposure to hand-arm vibration was an additional factor for shoulder pain (HR = 1.06 log increase/h of exposure: 95% CI, 1.01 to 1.10, P = 0.007). Manipulating heavy loads was a further risk factor for back and shoulder pain for women in electrical work. There were only 3 incident cases of Raynaud's syndrome in physician records: symptoms suggestive of VWF related strongly to work in cold environments but not to hand-arm vibration. Physician records of back pain did not reflect specific workplace demands, but physician records of shoulder/joint conditions were greater, overall, in those with longer exposure to whole-body vibration and to current hand-arm vibration in electrical workers.

CONCLUSION

Vibration, a well-recognized hazard, was a risk factor for all outcomes but with whole-body vibration more evidently a risk for welders and hand-arm vibration for electrical workers. The final models of risk factors differed importantly between the two trades, suggesting specific targets for intervention.

Related Concept Videos

Disorders of the Skeletal Muscle 01:28

906

The clinical conditions affecting the skeletal muscle tissue are broadly categorized as musculoskeletal and neuromuscular disorders.
Musculoskeletal disorders
Musculoskeletal disorders involve injuries and conditions affecting the skeletal muscles and associated connective tissues. These disorders can arise from acute biomechanical stresses or chronic overuse and can occur across different age groups. Common injuries include sprains, fractures, and muscular strains, often resulting from...

Hooke's Law 01:26

357

Hooke's law, a pivotal principle in material science, establishes that the strain a material undergoes is directly proportional to the applied stress, defined by a factor called the modulus of elasticity or Young's modulus.


 The implementation of Hooke's law holds true until the material reaches its proportional limit. Beyond this point, the stress-strain relationship becomes nonlinear. This limit often coincides with the yield point for materials that are ductile in nature....

Residual Stresses 01:26

207

Residual stresses reside in a structure even after removing the original stress inducer. This phenomenon often arises from varied plastic deformations across different parts of a structure. Consider a rod stretched beyond its yield point. It will not regain its original length due to permanent deformation. Even after load removal, the rod does not entirely lose stress because of uneven plastic deformations, resulting in residual stresses. The computation of these stresses in structures is...

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity 01:15

256

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.

Temperature Dependent Deformation 01:12

143

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...

Strain-Energy Density 01:20

389

Understanding the strain energy density in materials under axial load is crucial for evaluating their mechanical behavior and durability. When a rod is subjected to such a load, it elongates and stores energy, known as strain energy, as potential energy within the material. This energy is measured in terms of energy per unit volume.
In the elastic region of a material, the relationship between the stress and the strain is linear and follows Hooke's Law. The strain energy density in this...