Related Experiment Video

Updated: Sep 13, 2025

Author Spotlight: Introduction to Active Probe Atomic Force Microscopy with Quattro-Parallel Cantilever Arrays
05:04

Author Spotlight: Introduction to Active Probe Atomic Force Microscopy with Quattro-Parallel Cantilever Arrays

Published on: June 13, 2023

1.7K

Dual-circularly polarized flat-top-beam transmitarray antenna with flexible energy allocations

LinXiao Wu, Ke Chen, Mai Yan

    Optics Express
    |July 30, 2025
    PubMed

    More Related Videos

    Demonstration of Equal-Intensity Beam Generation by Dielectric Metasurfaces09:33

    Demonstration of Equal-Intensity Beam Generation by Dielectric Metasurfaces

    Published on: June 7, 2019

    6.4K
    Design, Fabrication, and Experimental Characterization of Plasmonic Photoconductive Terahertz Emitters10:54

    Design, Fabrication, and Experimental Characterization of Plasmonic Photoconductive Terahertz Emitters

    Published on: July 8, 2013

    15.0K

    Related Concept Videos

    Energy Stored In A Coaxial Cable01:31

    Energy Stored In A Coaxial Cable

    A coaxial cable consists of a central copper conductor used for transmitting signals, followed by an insulator shield, a metallic braided mesh that prevents signal interference, and a plastic layer that encases the entire assembly.
    In the simplest form, a coaxial cable can be represented by two long hollow concentric cylinders in which the current flows in opposite directions. The magnetic field inside and outside the coaxial cable is determined by using Ampère's law. The magnetic...
    1.7K
    Maximum Power Transfer01:16

    Maximum Power Transfer

    Numerous practical applications within engineering disciplines, such as telecommunications, necessitate optimizing power delivery to a connected load. This pursuit, however, entails inherent internal losses, which can either equal or exceed the power supplied to the load. The Thevenin equivalent circuit is helpful in finding the maximum power a linear circuit can deliver to a load. It is assumed in this context that the load resistance can be adjusted.
    By substituting the entire circuit with...
    414
    The Antenna Complex01:15

    The Antenna Complex

    Plants and other photosynthetic organisms comprise pigments capable of absorption of direct sunlight. These pigments are present in the reaction center - the main site of photochemical reactions as well as in the antenna complex. Under average light conditions, the rate at which reaction center pigments absorb light is far below the electron transport chain's capacity. As a result, the reaction center alone cannot provide enough energy to drive photosynthesis. The photosynthetic efficiency can...
    6.2K
    Transmission Line Design Considerations01:23

    Transmission Line Design Considerations

    Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
    215
    Generating Electromagnetic Radiations01:10

    Generating Electromagnetic Radiations

    The German physicist Heinrich Hertz (1857–1894) was the first to generate and detect certain types of electromagnetic waves in the laboratory. Starting in 1887, he performed a series of experiments that confirmed the existence of electromagnetic waves and verified that they travel at the speed of light. Hertz used an alternating-current RLC (resistor-inductor-capacitor) circuit that resonated at a known frequency and connected it to a loop of wire. High voltages induced across the gap in...
    4.0K
    Beams with Symmetric Loadings01:15

    Beams with Symmetric Loadings

    The moment-area method is an analytical tool used in structural engineering to determine the slope and deflection of beams under various loads. Consider a cantilever with a concentrated load and moment at the free end. The first step is constructing a free-body diagram to calculate the reactions at the fixed end. Next, the bending moment diagram is plotted to visualize how the bending moment varies along the beam's length, focusing on points where the bending moment equals zero.
    The M/EI...
    243