Related Experiment Video

Updated: Sep 11, 2025

Fiber Optic Distributed Sensors for High-resolution Temperature Field Mapping
09:48

Fiber Optic Distributed Sensors for High-resolution Temperature Field Mapping

Published on: November 7, 2016

12.1K

Simultaneous vibration and soil moisture sensing using a single mode fiber for structural health monitoring

James Jena, Francois Swanepoel, Gaathier Mahed

    Applied Optics
    |August 12, 2025
    PubMed

    More Related Videos

    Data Acquisition Protocol for Determining Embedded Sensitivity Functions07:46

    Data Acquisition Protocol for Determining Embedded Sensitivity Functions

    Published on: April 20, 2016

    6.2K
    In Situ Soil Moisture Sensors in Undisturbed Soils08:20

    In Situ Soil Moisture Sensors in Undisturbed Soils

    Published on: November 18, 2022

    6.6K

    Related Concept Videos

    Fiber Reinforced Concrete01:22

    Fiber Reinforced Concrete

    Fiber-reinforced concrete significantly enhances the structural and nonstructural properties of traditional concrete by incorporating fibers like steel, glass, and polymers. These fibers, varying from natural ones such as sisal and cellulose to manufactured ones like polypropylene and Kevlar, are mixed into hydraulic cement with aggregates. Steel fibers, often preferred for their robustness, contribute to improved ductility, toughness, and post-cracking performance. The concrete is classified...
    130
    Dynamic Modulus of Elasticity of Concrete01:16

    Dynamic Modulus of Elasticity of Concrete

    The dynamic modulus of elasticity assesses how a concrete structure deforms under impact or dynamic loads. It is typically higher than the static modulus of elasticity, measured under slow, steady loading conditions.
    The sonic test is a common method to determine the dynamic modulus. In this test, a concrete beam, sized either 6 x 6 x 30 inches or 4 x 4 x 20 inches, is clamped at its center. Vibrations are initiated at one end of the beam by an electromagnetic exciter unit powered by...
    540
    Vibrating Concrete01:19

    Vibrating Concrete

    Mechanical vibrators are instrumental in compacting newly poured concrete within formwork and around reinforcements. This process is essential to eliminate trapped air pockets and establish a dense concrete mass. One widely used method is vibrating by internal vibrators, often referred to as a poker vibrator or immersion vibrator. It is rapidly inserted through the full depth of the freshly laid concrete and slightly extends into the layer below it (which remains in a plastic state). Consistent...
    189
    Modes of Standing Waves - I01:03

    Modes of Standing Waves - I

    A close look at earthquakes provides evidence for the conditions appropriate for resonance, standing waves, and constructive and destructive interference. A building may vibrate for several seconds with a driving frequency matching the building's natural frequency of vibration; this produces a resonance that results in one building collapsing while the neighboring buildings do not. Often, buildings of a certain height are devastated, while other taller buildings remain intact. This...
    3.1K
    Elastic Strain Energy for Shearing Stresses01:20

    Elastic Strain Energy for Shearing Stresses

    As discussed in previous lessons, strain energy in a material is the energy stored when it is elastically deformed, a concept crucial in materials science and mechanical engineering. This energy results from the internal work done against the cohesive forces within the material. When a material undergoes shearing stress and corresponding shearing strain, the strain energy density, which is the energy stored per unit volume, is calculated. Within the elastic limit, where the stress is...
    284
    Design Example: Strain Gauge Bridge or Wheatstone Bridge01:15

    Design Example: Strain Gauge Bridge or Wheatstone Bridge

    The utilization of strain gauges as transducers for converting mechanical strain into electrical signals is a common practice in various engineering applications. These strain gauges are frequently integrated into Wheatstone bridge circuits to accurately measure parameters such as force or pressure. Within this context, each element within the circuit exhibits a resistance that undergoes subtle variations when subjected to mechanical strain. The primary objective is to convert minuscule...
    526