Related Experiment Video

Updated: Sep 9, 2025

Construction of a Wireless-Enabled Endoscopically Implantable Sensor for pH Monitoring with Zero-Bias Schottky Diode-based Receiver
08:25

Construction of a Wireless-Enabled Endoscopically Implantable Sensor for pH Monitoring with Zero-Bias Schottky Diode-based Receiver

Published on: August 27, 2021

2.7K

A 0.049 mm2 0.5-to-5.8 GHz LNA Achieving a Flat High Gain Based on an Active Inductor and Low Capacitive ESD

Dawei Dong1, Zhenrong Li1, You Quan1

  • 1School of Microelectronics, Xidian University, Xi'an 710126, China.

Micromachines
|August 28, 2025
PubMed

Keywords:
ESDSiGe HBTactive inductorlow noise amplifiernoise

More Related Videos

Fabrication and Characterization of Superconducting Resonators10:26

Fabrication and Characterization of Superconducting Resonators

Published on: May 21, 2016

11.5K
Calibration of Vector Network Analyzer for Measurements in Radio Frequency Propagation Channels10:00

Calibration of Vector Network Analyzer for Measurements in Radio Frequency Propagation Channels

Published on: June 2, 2020

21.4K

Related Concept Videos

Design Example: Capacitance Multiplier Circuit01:20

Design Example: Capacitance Multiplier Circuit

In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
953
Design Example: Underdamped Parallel RLC Circuit01:17

Design Example: Underdamped Parallel RLC Circuit

Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
Starting with a fixed...
376
Capacitor With A Dielectric01:18

Capacitor With A Dielectric

Parallel plate capacitors consist of two conducting plates separated by a certain distance. However, it is mechanically difficult to hold the large plates parallel to each other without actual contact. Hence, a dielectric layer is commonly placed between the plates, which provides an easy solution for holding the plates together with a small gap and increases the capacitance of the capacitor.
Dielectrics are non-conducting materials with no free or loosely bound electrons. When a dielectric is...
4.1K
Small-Signal Analysis of MOSFET Amplifiers01:23

Small-Signal Analysis of MOSFET Amplifiers

In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
732
MOSFET Amplifiers01:17

MOSFET Amplifiers

The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
221
Inductance: Solid Cylindrical Conductor01:24

Inductance: Solid Cylindrical Conductor

To calculate the inductance of a solid cylindrical conductor, consider a 1-meter section of a non-magnetic, current-carrying conductor with radius r. Disregarding end effects and assuming uniform current density, Ampere's law helps determine the magnetic field inside the conductor. This law states that the magnetic field intensity H is concentric and constant within the conductor.
Given the uniform current distribution, the magnetic field Hx and flux density Bx inside the conductor are...
376