Related Experiment Video

Updated: Jan 17, 2026

Original Experimental Approach for Assessing Transport Fuel Stability
09:48

Original Experimental Approach for Assessing Transport Fuel Stability

Published on: October 21, 2016

9.7K

Influence of Load in Formaldehyde and Acetaldehyde Emissions and Performance of a Diesel Engine Using Various

Oscar Edwin Piamba Tulcán1, Roberto Guimarães Pereira2, Carlos E Fellows3

  • 1Universidad Nacional de Colombia, University City, Carrera 30 # 45-03, 111321 Bogotá, Colombia.

ACS Omega
|September 22, 2025
PubMed

More Related Videos

Author Spotlight: Employing Green-Chemistry Principles for Safe and Sustainable Synthesis of Biodiesels04:40

Author Spotlight: Employing Green-Chemistry Principles for Safe and Sustainable Synthesis of Biodiesels

Published on: April 19, 2024

1.6K
Fluorescent Paper Strips for the Detection of Diesel Adulteration with Smartphone Read-out07:10

Fluorescent Paper Strips for the Detection of Diesel Adulteration with Smartphone Read-out

Published on: November 9, 2018

9.8K

Related Concept Videos

Otto and Diesel Cycle01:27

Otto and Diesel Cycle

An Otto engine is a four-stroke engine that uses a mixture of gasoline and air as the working fuel. The fuel is injected into the cylinder, and the piston is moved completely down so that the cylinder is at maximum volume. By moving the piston up, adiabatic compression takes place. The spark plug ignites the gasoline-air mixture, and the burning fuel adds heat to the system at a constant volume. The heated mixture expands adiabatically and gets further cooled by exhausting heat, and this cyclic...
3.5K
Work Done in an Adiabatic Process01:20

Work Done in an Adiabatic Process

Consider the adiabatic compression of an ideal gas in the cylinder of an automobile diesel engine. The gasoline vapor is injected into the cylinder of an automobile engine when the piston is in its expanded position. The temperature, pressure, and volume of the resulting gas-air mixture are 20 °C, 1.00 x 105 N/m2, and 240 cm3 , respectively. The mixture is then compressed adiabatically to a volume of 40 cm3. Note that, in the actual operation of an automobile engine, the compression is not...
4.1K
Turnover Number and Catalytic Efficiency01:19

Turnover Number and Catalytic Efficiency

The turnover number of an enzyme is the maximum number of substrate molecules it can transform per unit time. Turnover numbers for most enzymes range from 1 to 1000 molecules per second. Catalase has the known highest turnover number, capable of converting up to 2.8×106 molecules of hydrogen peroxide into water and oxygen per second. Lysozyme has the lowest known turnover number of half a molecule per second.
Chymotrypsin is a pancreatic enzyme that breaks down proteins during digestion....
20.2K
Combustion Energy: A Measure of Stability in Alkanes and Cycloalkanes02:14

Combustion Energy: A Measure of Stability in Alkanes and Cycloalkanes

The low reactivity in alkanes can be attributed to the non-polar nature of C–C and C–H σ bonds. Alkanes, therefore, were  initially termed as “paraffins,” derived from the Latin words: parum, meaning “too little,” and affinis, meaning “affinity.”
Alkanes undergo combustion in the presence of excess oxygen and high-temperature conditions to give carbon dioxide and water. A combustion reaction is the energy source in natural gas, liquified...
7.7K
Internal Combustion Engine01:20

Internal Combustion Engine

The internal combustion engine is a heat engine that uses the byproducts of combustion as the working fluid instead of using a heat transfer medium to transfer heat. The combustion is done in a way that produces high-pressure combustion products that can be expanded through a turbine or piston to create work. Internal combustion engines can again be categorized into three kinds: (1) spark ignition gasoline engines, most commonly used in automobiles, (2) compression ignition diesel engines that...
2.6K