Related Experiment Video

Updated: Jan 9, 2026

Data Processing Methods for 3D Seismic Imaging of Subsurface Volcanoes: Applications to the Tarim Flood Basalt
07:58

Data Processing Methods for 3D Seismic Imaging of Subsurface Volcanoes: Applications to the Tarim Flood Basalt

Published on: August 7, 2017

9.9K

Asynchronous transfer of magmas and mineralizing fluids in a plutonic-subvolcanic-volcanic plumbing system

Gabriele Paoli1,2, Andrea Dini3, Simone Vezzoni4

  • 1Dipartimento di Scienze Della Terra, Università di Pisa, Pisa, Italy. gabriele.paoli@unipi.it.

Scientific Reports
|December 5, 2025
PubMed

More Related Videos

Atom Probe Tomography Analysis of Exsolved Mineral Phases08:14

Atom Probe Tomography Analysis of Exsolved Mineral Phases

Published on: October 25, 2019

7.7K
Metal-silicate Partitioning at High Pressure and Temperature: Experimental Methods and a Protocol to Suppress Highly Siderophile Element Inclusions11:50

Metal-silicate Partitioning at High Pressure and Temperature: Experimental Methods and a Protocol to Suppress Highly Siderophile Element Inclusions

Published on: June 13, 2015

12.9K

Related Concept Videos

Multiple Pipe Systems01:21

Multiple Pipe Systems

Multipipe systems consist of complex configurations of interconnected pipes designed to transport fluids efficiently across intricate networks. They are essential in engineering applications requiring precise control over flow distribution, pressure, and head loss. They are categorized into series, parallel, loop, and network configurations, each distinguished by unique flow characteristics and applications.
Series Configuration
In a series configuration, fluid flows sequentially from one pipe...
1.1K
Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
415
Isothermal Processes01:21

Isothermal Processes

A thermodynamic process that occurs at constant temperature is called an isothermal process. Heat slowly flows into the system or out of the system to maintain thermal equilibrium. Processes involving phase changes like water evaporation into steam or freezing water into ice at a constant temperature are examples of Isothermal Processes.
An ideal gas can also undergo isothermal expansion or compression.
For example, consider 1 mole of an ideal gas inside an isolated cylinder at initial volume V...
4.8K
Design Example: Designing a Residential Plumbing System01:25

Design Example: Designing a Residential Plumbing System

The design of residential plumbing systems requires carefully evaluating water demand, flow rates, and pressure dynamics to ensure both efficiency and reliability. The nature of water flow within pipes is defined by its Reynolds number, which classifies flow as either laminar (smooth) or turbulent.
1.1K
Cavity Drainage and Flashings in Masonry walls01:20

Cavity Drainage and Flashings in Masonry walls

Typically, a cavity wall consists of two wythes separated by a gap of at least 2 inches, which may contain insulation while still maintaining a minimum clear space of 1 inch to facilitate adequate drainage. Advanced methods like the insertion of a continuous drainage mat can further reduce this space while ensuring effective moisture expulsion.
Weep holes, strategically placed at the base of the cavity, are critical for draining accumulated water. These openings are created by leaving head...
393
Sulfur Assimilation01:20

Sulfur Assimilation

Sulfur is an essential element in biological systems, contributing to synthesizing key biomolecules, including amino acids such as cysteine and methionine, and cofactors such as coenzyme A and biotin. Microorganisms primarily assimilate sulfur as sulfate (SO₄²⁻) from the environment, which must undergo a series of biochemical transformations before it can be incorporated into cellular components. As sulfate is highly oxidized, it must undergo assimilatory sulfate reduction to...
301