Related Experiment Video

Updated: Feb 4, 2026

Guided Endodontics: Three-Dimensional Planning and Template-Aided Preparation of Endodontic Access Cavities
07:14

Guided Endodontics: Three-Dimensional Planning and Template-Aided Preparation of Endodontic Access Cavities

Published on: May 24, 2022

5.2K

Evaluation of fracture resistance among endodontically treated teeth using constant, variable and guiding taper

Sonam Bohra1, Gurudutt Nayak1, Maulsree Guleria1

  • 1Department of Conservative Dentistry and Endodontics, Mansarovar Dental College, Bhopal, Madhya Pradesh, India.

Bioinformation
|February 2, 2026
PubMed

Keywords:
Fracture resistanceJIZAIProTaper UltimateXP-endo riserotary filevertical root fracture

More Related Videos

Dynamic Navigation in Endodontics: Guided Access Cavity Preparation by Means of a Miniaturized Navigation System07:03

Dynamic Navigation in Endodontics: Guided Access Cavity Preparation by Means of a Miniaturized Navigation System

Published on: May 5, 2022

5.3K
Scanning Electron Microscopic Evaluation of Surface Defects of Remover Retreatment File After Single and Multiple Uses03:07

Scanning Electron Microscopic Evaluation of Surface Defects of Remover Retreatment File After Single and Multiple Uses

Published on: October 11, 2024

1.0K

Related Concept Videos

Systems of Linear Equations in Two Variables01:25

Systems of Linear Equations in Two Variables

Solving a system of linear equations is a fundamental concept in algebra. A system of equations consists of two or more linear equations involving the same set of variables. One of the most efficient algebraic methods for solving such systems is the substitution method. This technique involves expressing one variable in terms of the other from one equation and substituting it into the second equation. This method is particularly useful when one of the equations is easily rearranged.Consider the...
306
Multi-input and Multi-variable systems01:22

Multi-input and Multi-variable systems

Cruise control systems in cars are designed as multi-input systems to maintain a driver's desired speed while compensating for external disturbances such as changes in terrain. The block diagram for a cruise control system typically includes two main inputs: the desired speed set by the driver and any external disturbances, such as the incline of the road. By adjusting the engine throttle, the system maintains the vehicle's speed as close to the desired value as possible.
In the absence of...
423
Teeth01:15

Teeth

The formation of teeth, also known as odontogenesis, is a complex process that begins in utero, around the sixth week of embryonic development. There are three stages to this process: the bud stage, the cap stage, and the bell stage.
In the bud stage, the tooth germ (an aggregation of cells) starts to form in the developing jawbone. During the cap stage, the tooth germ differentiates into enamel organ, dental papilla, and dental sac, which will later develop into the tooth's enamel, dentin...
1.8K
Constant Pressure Calorimetry03:02

Constant Pressure Calorimetry

Calorimetry is a technique used to measure the amount of heat involved in a chemical or physical process or to measure the heat transferred to or from a substance. The heat is exchanged with a calibrated and insulated device called the calorimeter. Calorimetry experiments are based on the assumption that there is no heat exchange between the insulated calorimeter and the external environment. The well-insulated calorimeters prevent the transfer of heat between the calorimeter and its external...
97.7K
Constant Volume Calorimetry02:41

Constant Volume Calorimetry

Calorimeters are useful to determine the heat released or absorbed by a chemical reaction. Coffee cup calorimeters are designed to operate at constant (atmospheric) pressure and are convenient to measure heat flow (or enthalpy change) accompanying processes that occur in solution at constant pressure. A different type of calorimeter that operates at constant volume, colloquially known as a bomb calorimeter, is used to measure the energy produced by reactions that yield large amounts of heat and...
30.8K
Calculating the Equilibrium Constant02:46

Calculating the Equilibrium Constant

The equilibrium constant for a reaction is calculated from the equilibrium concentrations (or pressures) of its reactants and products. If these concentrations are known, the calculation simply involves their substitution into the Kc expression.
For example, gaseous nitrogen dioxide forms dinitrogen tetroxide according to this equation:
38.0K