Related Experiment Video

Updated: Feb 7, 2026

A New Ex Vivo Model for the Evaluation of Endoscopic Submucosal Injection Material Performance
03:54

A New Ex Vivo Model for the Evaluation of Endoscopic Submucosal Injection Material Performance

Published on: October 19, 2018

6.6K

Utilization of methylene blue-based submucosal injection to identify residual neuroendocrine tumor in the colon after

Weina Jing1,2, Yuxiang Chen1,2, Kai Deng1,2

  • 1Department of Gastroenterology & Hepatology, West China Hospital, Sichuan University, Chengdu, Sichuan, China.

Igie : Innovation, Investigation and Insights
|February 6, 2026
PubMed

More Related Videos

The Application of 1% Methylene Blue Dye As a Single Technique in Breast Cancer Sentinel Node Biopsy07:51

The Application of 1% Methylene Blue Dye As a Single Technique in Breast Cancer Sentinel Node Biopsy

Published on: June 1, 2019

21.4K
Assessing Urinary Tract Junction Obstruction Defects by Methylene Blue Dye Injection06:05

Assessing Urinary Tract Junction Obstruction Defects by Methylene Blue Dye Injection

Published on: October 12, 2017

16.2K

Related Concept Videos

Residual Plots01:07

Residual Plots

A residual plot is a statistical representation of data used to analyze correlation and regression results. It helps verify the requirements for drawing specific conclusions about correlation and regression. To obtain the residual plot, first, the residual for each data value is calculated, which is simply the vertical distance between the observed and the predicted value obtained from the regression equation.
When the residual values are plotted against the variable x, it is called a residual...
6.5K
Residual Stresses01:26

Residual Stresses

Residual stresses reside in a structure even after removing the original stress inducer. This phenomenon often arises from varied plastic deformations across different parts of a structure. Consider a rod stretched beyond its yield point. It will not regain its original length due to permanent deformation. Even after load removal, the rod does not entirely lose stress because of uneven plastic deformations, resulting in residual stresses. The computation of these stresses in structures is...
652
The Colonization of Land02:22

The Colonization of Land

Changes in the environment of the early Earth drove the evolution of organisms. As prokaryotic organisms in the oceans began to photosynthesize, they produced oxygen. Eventually, oxygen saturated the oceans and entered the air, resulting in an increase in atmospheric oxygen concentration, known as the oxygen revolution approximately 2.3 billion years ago. Therefore, organisms that could use oxygen for cellular respiration had an advantage. More than 1.5 years ago, eukaryotic cells and...
37.7K
Gas Chromatography: Sample Injection Systems01:08

Gas Chromatography: Sample Injection Systems

In gas chromatography, the sample is introduced as a vapor plug into the carrier gas stream for high efficiency and resolution. A microsyringe injects the sample solution into a heated sample port, vaporizing it and mixing it with the carrier gas. This process is important to ensure the sample is properly prepared for analysis. Thermally sensitive samples can be injected directly into the column and volatilized by slowly increasing the column temperature.
Two primary injection methods are used...
1.6K
Residual Stresses in Circular Shafts01:10

Residual Stresses in Circular Shafts

In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
546
Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
569