Related Experiment Video

Updated: Feb 12, 2026

Determination of the Mechanical Properties of Flexible Connectors for Use in Insulated Concrete Wall Panels
05:26

Determination of the Mechanical Properties of Flexible Connectors for Use in Insulated Concrete Wall Panels

Published on: October 19, 2022

2.0K

Effect of CaO content in Class C fly ash on the deformation properties of fully-graded concrete

Longsheng Qin1, Miaomiao Gong2, Hongfei Zhang3

  • 1Xinjiang Water Resources Development and Construction Group Co. Ltd, Urumqi, 830000, China.

Scientific Reports
|February 10, 2026
PubMed

Keywords:
CaOClass C fly ashDeformation performanceFully-graded concrete

More Related Videos

A Colorimetric Method for Measuring Iron Content in Plants07:12

A Colorimetric Method for Measuring Iron Content in Plants

Published on: September 7, 2018

23.0K
Building Double-decker Traps for Early Detection of Emerald Ash Borer06:07

Building Double-decker Traps for Early Detection of Emerald Ash Borer

Published on: October 4, 2017

8.2K

Related Concept Videos

Measurement of Air Content in Concrete01:23

Measurement of Air Content in Concrete

Air content measurement in concrete is critical for ensuring structural integrity and durability of concrete structures, especially in environments prone to severe weather conditions. Accurate air content analysis optimizes concrete's resistance to freeze-thaw cycles and enhances its workability and strength. Several methods are standardized under ASTM guidelines to measure the air content in fresh concrete, each suitable for different concrete types and conditions.
The pressure method,...
679
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
477
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
477
Graded Potential01:19

Graded Potential

Graded potentials are localized fluctuations in the cell membrane's electrical charge, commonly found in the dendrites of neurons. The magnitude of these potential changes depends on the strength of the initiating stimulus. In a membrane at its resting potential, a graded potential signifies a voltage shift either above -70 mV or below -70 mV.
Graded potentials fall into two categories: depolarizing and hyperpolarizing. Depolarizing graded potentials typically occur when sodium (Na+) or...
7.1K
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
415
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
528