Endoscopic Flexor Hallucis Longus Tenotomy for Post-traumatic Checkrein Deformity: A Case Report

Related Experiment Video

Updated: Feb 12, 2026

Murine Flexor Tendon Injury and Repair Surgery
07:32

Murine Flexor Tendon Injury and Repair Surgery

Published on: September 19, 2016

13.7K

Banoth Valya1, P Savithri Devi1, Nittala Bhavya1

  • 1Department of Orthopaedics, Gandhi Medical College and Hospital, Secunderabad, Telangana, India.

Journal of Orthopaedic Case Reports
|February 11, 2026
PubMed
Abstract

Keywords:
Checkrein deformityendoscopic tenotomyflexor hallucis longushindfoot arthroscopytibial fracture

More Related Videos

Inducing Post-Traumatic Epilepsy in a Mouse Model of Repetitive Diffuse Traumatic Brain Injury07:07

Inducing Post-Traumatic Epilepsy in a Mouse Model of Repetitive Diffuse Traumatic Brain Injury

Published on: February 10, 2020

11.3K
Author Spotlight: Isolation of Long Muscle Fibers from Mouse Hindlimb Muscles for Studying Excitation-Contraction Coupling Across Fiber Types08:12

Author Spotlight: Isolation of Long Muscle Fibers from Mouse Hindlimb Muscles for Studying Excitation-Contraction Coupling Across Fiber Types

Published on: December 1, 2023

3.6K

Related Concept Videos

Post-traumatic Stress Disorder01:27

Post-traumatic Stress Disorder

Post-traumatic stress disorder (PTSD) is a psychiatric condition that arises following exposure to traumatic events such as natural disasters, forced displacement, or severe accidents. It significantly impairs individuals' ability to cope with daily activities and disrupts their emotional and psychological equilibrium.
Symptoms and Behavioral Manifestations
A spectrum of distressing symptoms characterizes PTSD. Recurrent flashbacks, where individuals involuntarily relive traumatic events,...
590
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
477
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
477
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
415
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
528
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
491