Related Experiment Video

Updated: Jun 6, 2026

A Reliable and Reproducible Critical-Sized Segmental Femoral Defect Model in Rats Stabilized with a Custom External Fixator
08:20

A Reliable and Reproducible Critical-Sized Segmental Femoral Defect Model in Rats Stabilized with a Custom External Fixator

Published on: March 24, 2019

9.4K

Suture button compared with ventral augmentation in unstable syndesmotic injuries : does it affect the quality of

Anne Scheuer1, Fabian T Spindler1, Wolfgang Böcker1

  • 1Department of Orthopaedics and Trauma Surgery, Musculoskeletal University Center Munich, University Hospital, LMU Munich, Munich, Germany.

The Bone & Joint Journal
|February 28, 2026
PubMed
Abstract

More Related Videos

Using Q Suture to Enhance Resistance to Gap Formation and Tensile Strength of Repaired Flexor Tendons10:32

Using Q Suture to Enhance Resistance to Gap Formation and Tensile Strength of Repaired Flexor Tendons

Published on: June 3, 2020

6.4K
Application of a New Mesh Fixation Method in Laparoscopic Incisional Hernia Repair05:15

Application of a New Mesh Fixation Method in Laparoscopic Incisional Hernia Repair

Published on: December 23, 2022

7.6K

Related Concept Videos

Stability of Equilibrium Configuration01:23

Stability of Equilibrium Configuration

Understanding the stability of equilibrium configurations is a fundamental part of mechanical engineering. In any system, there are three distinct types of equilibrium: stable, neutral, and unstable.
A stable equilibrium occurs when a system tends to return to its original position when given a small displacement, and the potential energy is at its minimum. An example of a stable equilibrium is when a cantilever beam is fixed at one end and a weight is attached to the other end. If the weight...
Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller width...
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress concentration...
Herniated Intervertebral Disc l: Introduction01:29

Herniated Intervertebral Disc l: Introduction

Intervertebral disc herniation refers to the displacement of the nucleus pulposus (the gel-like inner core of the disc) through a tear or weakened area in the annulus fibrosus (the outer fibrous ring). The displaced disc material extends beyond the normal boundaries of the disc space and may compress or irritate nearby spinal nerve roots or, less commonly, the spinal cord.Etiology and Risk FactorsHerniation commonly results from degeneration, in which aging reduces disc hydration and...
Degenerative Disc Disease ll: Pathophysiology01:23

Degenerative Disc Disease ll: Pathophysiology

The symptoms of degenerative disc disease arise from a combination of mechanical compression, vascular compromise, and biochemical inflammation, which together disrupt nerve function and produce pain.Mechanical CompressionDisc degeneration reduces height and elasticity, predisposing to herniation of the nucleus pulposus, a major cause of radicular pain. Herniations may be protrusion (bulging with intact annulus), extrusion (nucleus extends beyond disc but remains connected), or sequestration...