Related Experiment Video
Updated: Apr 2, 2026
An Intramedullary Locking Nail for Standardized Fixation of Femur Osteotomies to Analyze Normal and Defective Bone Healing in Mice
Published on: November 13, 2016
Are continuous locking headless bone screws with locking plate fixation effective for bridging fracture gaps in far
Chen-Chiang Lin1, Ya-Han Chan2, Po-Feng Su3
1Department of Orthopedics, National Taiwan University Hospital Yun-Lin Branch, Douliou, Yunlin, Taiwan.
Introduction:
Locking screws typically provide more stable fixation than conventional cortical screws. However, the rigid connection between the locking screw head and plate hole can cause stress concentrations and lead to early failure under cyclic loading. This study aimed to compare the mechanical stability of a continuous (headless) locking screw with standard locking screws and cortical screws, either in a standard (flush with the bone) or in far cortical locking constructs, using biomechanical testing and finite element analysis (FEA).
Methods:
The Trident Distal Radial Locking Plate (A-Plus Biotechnology Co., Ltd., Taiwan) was used to repair a simulated distal radial diaphysis fracture and was secured to the bone using different screw types. The fracture gap was bridged with the plate placed flush with the bone and with the plate offset from the bone surface by 4 mm (far cortical locking (FCL)). The constructs were subjected to static compression and cyclic axial loading tests to assess construct stiffness and yield load, as well as endurance and failure mechanisms under cyclic loading, while FEA was used to evaluate the von Mises stress distribution on the plates and screws.
Results:
The Group 3a (flush with bone, continuous locking screws) had a significantly higher yield load than Groups 2b (FCL with locking screws) and 3b (FCL with continuous locking screws) (p < 0.05). In addition, Group 1 (flush with bone, cortical screws) was found to be significantly stiffer than Groups 2b and 3b (p < 0.01). For the dynamic testing, Group 3a showed intermediate endurance and failed predominantly by screw pull-out, whereas Groups 1 and 2 primarily failed by plate deformation. The FEA results showed stress concentrations at the screw neck of the standard locking screws and around the threaded regions of the continuous locking screws.
Conclusion:
Continuous locking screws placed flush with the bone had the greatest fixation strength of all configurations tested. However, using continuous locking screws in an FCL configuration may redirect stress to the threaded region of the screw neck, potentially increasing the risk of failure.
More Related Videos
15:11Surgical Fixation of Sternal Fractures: Preoperative Planning and a Safe Surgical Technique Using Locked Titanium Plates and Depth Limited Drilling
Published on: January 5, 2015
04:19Minimally Invasive Treatment for Thoracolumbar Burst Fracture Using Sagittal Alignment Screws and A Trauma Reduction Device
Published on: November 8, 2024
Related Concept Videos
01:16Self-Locking Screw
A square-threaded screw jack carrying a load is considered self-locking if the screw retains its position even after the moment applied to it is removed.
01:17Frictional Forces on Screws
A jack with a square-threaded screw is a mechanical device used to lift heavy loads by applying a force at its handle. When the force is applied, the screw turns, raising the load. The screw can...
01:27Fractures: Bone Repair
Minor fractures with no bone displacement are treated by immobilizing the fractured bone using a cast or splint. However, in the case of fractures with displaced bones, the broken bones are repositioned before immobilization to ensure successful healing without deformation and loss of function. The realignment of fractured bone ends is performed through a process called reduction. If the...
01:22Sutures of the Skull
Sutures are immobile joints between adjacent bones of the skull. The narrow gap between the bones is filled with dense, fibrous connective tissue that unites the bones. The long sutures located between the skull bones are not straight but instead follow irregular, tightly twisting paths. These twisting lines tightly...