Related Experiment Video

Updated: May 17, 2026

Synthesis and Microdiffraction at Extreme Pressures and Temperatures
07:26

Synthesis and Microdiffraction at Extreme Pressures and Temperatures

Published on: October 7, 2013

Sublithospheric diamond constraints on the state of deeply subducted slabs

Qiwei Zhang1,2, Frank E Brenker3, Suzette Timmerman4

  • 1Department of Earth and Atmospheric Sciences, University of Alberta, Edmonton, T6G 2E3, Canada.

Science Advances
|May 15, 2026
PubMed

More Related Videos

Characterization of Ultra-fine Grained and Nanocrystalline Materials Using Transmission Kikuchi Diffraction09:13

Characterization of Ultra-fine Grained and Nanocrystalline Materials Using Transmission Kikuchi Diffraction

Published on: April 1, 2017

Simulation of the Planetary Interior Differentiation Processes in the Laboratory06:04

Simulation of the Planetary Interior Differentiation Processes in the Laboratory

Published on: November 15, 2013

Related Concept Videos

Deep Sea Microbial Ecology01:18

Deep Sea Microbial Ecology

The deep ocean and its underlying sediments represent vast, largely unexplored microbial habitats that extend far beyond the sunlit photic zone. The photic (euphotic) zone typically spans the upper ~100–200 meters of pelagic waters in the open ocean, but its depth varies geographically and seasonally, where sufficient light supports photosynthetic life. Below this lies the deep sea, spanning roughly 1000–6000 meters (bathypelagic to abyssal zones), with deeper hadal trenches extending beyond...
Quarrying of Stone01:15

Quarrying of Stone

Quarrying is the process of extracting stone from a quarry, where specialized techniques are employed to remove large blocks of stone safely and efficiently. This process can involve controlled explosions or more precision-oriented methods such as cutting and drilling.
One common method involves using a diamond belt saw to cut large blocks from the quarry face. These blocks can be about 50 feet long and 12 feet high. After the initial vertical cut, drilling is performed at the base of the block.
Constraints and Statical Determinacy01:26

Constraints and Statical Determinacy

In structural engineering, the equilibrium of a system is not only determined by its equations of equilibrium but also with the help of constraints. Constraints refer to restrictions on the motion of a system. The proper combinations of constraints can minimize the total number of constraints needed to maintain a system in mechanical equilibrium. When this happens, the system is said to be statically determinate. For such systems, the unknown reaction supports can be estimated using equilibrium...
Phase Transitions: Sublimation and Deposition02:33

Phase Transitions: Sublimation and Deposition

Some solids can transition directly into the gaseous state, bypassing the liquid state, via a process known as sublimation. At room temperature and standard pressure, a piece of dry ice (solid CO2) sublimes, appearing to gradually disappear without ever forming any liquid. Snow and ice sublimate at temperatures below the melting point of water, a slow process that may be accelerated by winds and the reduced atmospheric pressures at high altitudes. When solid iodine is warmed, the solid sublimes...
Network Covalent Solids02:18

Network Covalent Solids

Network covalent solids contain a three-dimensional network of covalently bonded atoms as found in the crystal structures of nonmetals like diamond, graphite, silicon, and some covalent compounds, such as silicon dioxide (sand) and silicon carbide (carborundum, the abrasive on sandpaper). Many minerals have networks of covalent bonds.
To break or to melt a covalent network solid, covalent bonds must be broken. Because covalent bonds are relatively strong, covalent network solids are typically...
Yield Criteria for Ductile Materials under Plane Stress01:25

Yield Criteria for Ductile Materials under Plane Stress

In designing structural elements and machine parts using ductile materials, it is crucial to ensure that these components withstand applied stresses without yielding. Yielding is initially determined through a tensile test, which evaluates the material's response to uniaxial stress. However, tensile stress is insufficient when components face biaxial or plane stress conditions This condition requires advanced criteria to predict failure.
The Maximum Shearing Stress Criterion, also known as the...