Related Experiment Video

Updated: May 17, 2026

Asymmetric Thermoelectrochemical Cell for Harvesting Low-grade Heat under Isothermal Operation
09:09

Asymmetric Thermoelectrochemical Cell for Harvesting Low-grade Heat under Isothermal Operation

Published on: February 5, 2020

Beyond constant-temperature reservoirs: A Stirling cycle with constant heat-generation rate

Xinshu Xia1, Hongbo Huang1, Hui Dong1

  • 1China Academy of Engineering Physics, Beijing, Graduate School of , 100193, China.

Physical Review. E
|May 16, 2026
PubMed
Abstract

More Related Videos

Cryogenic Liquid Jets for High Repetition Rate Discovery Science08:34

Cryogenic Liquid Jets for High Repetition Rate Discovery Science

Published on: May 9, 2020

Rapid PCR Thermocycling using Microscale Thermal Convection09:02

Rapid PCR Thermocycling using Microscale Thermal Convection

Published on: March 5, 2011

Related Concept Videos

The Carnot Cycle01:30

The Carnot Cycle

Converting work to heat is an irreversible process, and the purpose of a heat engine is to reverse the effect partially. Heat engines aim to increase the efficiency of the reversal, that is, maximize the work retrieved from heat. If the efficiency of a heat engine were 100%, it would imply reversing the process completely without introducing any other effect. Thus, it would violate the second law of thermodynamics.
What could be the theoretical limit to the efficiency of a heat engine? The...
Efficiency of The Carnot Cycle01:16

Efficiency of The Carnot Cycle

The hypothetical Carnot cycle consists of an ideal gas subjected to two isothermal and two adiabatic processes. Since the internal energy of an ideal gas depends only on its temperature, which is the same before and after the completion of the Carnot cycle, there is no change in its internal energy. Hence, using the first law of thermodynamics, the total heat exchanged by the ideal gas equals the total work done. Thus, we can quantify the efficiency of the Carnot cycle via the heat exchanged...
The Carnot Cycle and the Second Law of Thermodynamics01:20

The Carnot Cycle and the Second Law of Thermodynamics

The Carnot engine works between two heat reservoirs of fixed temperatures. The Carnot cycle begs the following question: Is it possible to devise a heat engine that is more efficient than a Carnot engine between two fixed temperatures? The answer lies in designing a Carnot refrigerator.
Since the individual steps in a Carnot cycle can be reversed, the entire cycle is, thus, reversible. If a Carnot cycle is reversed, it becomes a Carnot refrigerator. It extracts heat Qc from a cold reservoir at...
Isothermal Processes01:21

Isothermal Processes

A thermodynamic process that occurs at constant temperature is called an isothermal process. Heat slowly flows into the system or out of the system to maintain thermal equilibrium. Processes involving phase changes like water evaporation into steam or freezing water into ice at a constant temperature are examples of Isothermal Processes.
An ideal gas can also undergo isothermal expansion or compression.
For example, consider 1 mole of an ideal gas inside an isolated cylinder at initial volume V...
Carnot Cycle and Efficiency01:26

Carnot Cycle and Efficiency

The Second Law of Thermodynamics asserts that it's impossible for any heat engine to achieve 100% efficiency. While contemplating the maximum possible efficiency, Nicolas Sadi Carnot conceptualized an ideal heat engine. This engine gets its energy from a high-temperature reservoir. It then performs some work and releases the remaining energy into a low-temperature reservoir.The Carnot cycle, named after Sadi Carnot, is fully reversible. The cycle consists of four distinct stages. In the first...
Cyclic Processes And Isolated Systems01:19

Cyclic Processes And Isolated Systems

A thermodynamic system with zero heat exchange and work is an isolated system. For these systems, the internal energy remains constant.
In the case of a non-isolated system, the change in the internal energy is zero only if the process is cyclic. A thermodynamic process is considered cyclic if the system undergoes a series of changes and returns to its initial state. 
Consider a cyclic process that returns to its initial state, undergoing a four-step process. The heat transfer along each path...