Related Experiment Video

Updated: May 27, 2026

Spark Plasma Sintering Apparatus Used for the Formation of Strontium Titanate Bicrystals
11:17

Spark Plasma Sintering Apparatus Used for the Formation of Strontium Titanate Bicrystals

Published on: February 9, 2017

Evolution of intragranular pores in potassium niobate ceramics during sintering

Xian-Xian Cai1, Zhaonian Zhou2, Yeming Huang3

  • 1State Key Laboratory of New Ceramic Materials, School of Materials Science and Engineering, Tsinghua University, Beijing, China.

Nature Communications
|May 25, 2026
PubMed

Keywords:
ceramic sinteringniobate materialspore evolutionmicrostructural analysis

More Related Videos

Fine-tuning the Size and Minimizing the Noise of Solid-state Nanopores09:43

Fine-tuning the Size and Minimizing the Noise of Solid-state Nanopores

Published on: October 31, 2013

Synthesis of Non-uniformly Pr-doped SrTiO3 Ceramics and Their Thermoelectric Properties11:07

Synthesis of Non-uniformly Pr-doped SrTiO3 Ceramics and Their Thermoelectric Properties

Published on: August 15, 2015

Related Concept Videos

Porosity in Cement Paste01:18

Porosity in Cement Paste

The porosity of concrete is a measure of the void spaces within its structure. These spaces impact its strength and durability significantly. When water and cement interact, a chemical reaction called hydration creates a semi-solid paste. This paste includes combined water, making up approximately 23% of the cement's dry mass, and gel water, which fills minuscule voids known as gel pores, accounting for about 28% of the cement gel volume.
The balance of water to cement in the mix is critical—it...
Pore Size Distribution01:23

Pore Size Distribution

In concrete, the pore size distribution significantly influences the material's properties. Capillary pores, markedly larger than gel pores, form a vast network within partially hydrated cement paste, reducing the concrete's strength and increasing its permeability. This heightened permeability leads to a greater risk of damage from environmental factors like freeze-thaw cycles and chemical attacks, with the extent of vulnerability also being tied to the water-to-cement ratio.
Adequate...
Porosity and Absorption of Aggregate01:20

Porosity and Absorption of Aggregate

Aggregates contain pores of varying sizes; while some are completely enclosed within the particles, others open onto the surface, allowing water to penetrate. The porosity of aggregates is a major factor contributing to the overall porosity of concrete, given that aggregates constitute about three-quarters of concrete's volume.
When all pores in an aggregate are filled with water, the aggregate is considered saturated and surface-dry. If left in dry air, water will evaporate until the aggregate...
Pore Transport and Ion-Pair Transport01:17

Pore Transport and Ion-Pair Transport

Pore transport and ion-pair formation are critical mechanisms for the absorption and distribution of drugs in the body.
Pore transport, also known as convective transport, is a process where small molecules like urea, water, and sugars rapidly cross cell membranes as though there were channels or pores in the membrane. Although direct microscopic evidence is limited  but the concept of pores or channels is widely accepted based on physiological evidence. Despite the lack of direct microscopic...
Structure of Porins01:21

Structure of Porins

Mitochondria, chloroplasts, and gram-negative bacteria have transmembrane, beta-barrel proteins called porins to mediate the free diffusion of ions and metabolites across the membrane. Mitochondrial porin precursors contain conserved amino acid sequences called beta signals at their C-terminal. Beta signals have a  motif of PoXGXXHyXHy (Po-Polar, X-Any amino acid, G-Glycine, Hy-LargeHydrophobic), which are crucial for precursor recognition to initiate precursor assembly. Beta-barrel precursors...
Permeability of Concrete01:25

Permeability of Concrete

Permeability in the context of concrete refers to how easily liquids or gases can pass through the material. This quality is crucial for assessing the water-tightness and durability of concrete structures and their resistance to chemical attacks. Concrete permeability can be determined through comparative laboratory tests. These tests typically involve sealing a concrete specimen from the sides, applying water pressure to the top surface with pressure, and measuring the amount of water passing...