Related Experiment Video

Updated: Jun 27, 2026

Parametric Optimization Design Method for Friction Plates of Hydro-Viscous Clutches
10:58

Parametric Optimization Design Method for Friction Plates of Hydro-Viscous Clutches

Published on: July 22, 2025

Determination of the Effective Parameters for Estimating the Temperature Mode at Braking

Aleksander Yevtushenko1

  • 1Faculty of Mechanical Engineering, Bialystok University of Technology, 45C Wiejska Street, 15-351 Bialystok, Poland.

Materials (Basel, Switzerland)
|June 26, 2026
PubMed
Abstract

Keywords:
brakingfriction heatingheat accumulationtemperature modethermal surface layer

More Related Videos

Tactile Vibrating Toolkit and Driving Simulation Platform for Driving-Related Research07:15

Tactile Vibrating Toolkit and Driving Simulation Platform for Driving-Related Research

Published on: December 18, 2020

Related Concept Videos

Friction: Problem Solving01:17

Friction: Problem Solving

Friction is an essential force that influences the motion of objects in daily life. Depending on the situation, it can be either beneficial or problematic. Consider a bus with a mass of three megagrams and its center of mass at a specific point, moving along a banked road at a constant speed. The coefficient of static friction between the tires and the road is 0.5. Find the maximum angle of the banked road at which the bus would not slip or tip.
Initially, a visual representation of the...
Efficiency of The Carnot Cycle01:16

Efficiency of The Carnot Cycle

The hypothetical Carnot cycle consists of an ideal gas subjected to two isothermal and two adiabatic processes. Since the internal energy of an ideal gas depends only on its temperature, which is the same before and after the completion of the Carnot cycle, there is no change in its internal energy. Hence, using the first law of thermodynamics, the total heat exchanged by the ideal gas equals the total work done. Thus, we can quantify the efficiency of the Carnot cycle via the heat exchanged...
PID Controller01:19

PID Controller

Proportional-Integral-Derivative (PID) controllers are widely used in various control systems to enhance stability and performance. In a thermostat, it adjusts heating or cooling based on the temperature difference between the actual and desired levels. They are often used in automotive speed systems, effectively managing sudden speed changes while maintaining a constant speed under varying conditions. On the other hand, PI controllers, commonly employed in voltage regulation, enhance stability...
Temperature Dependence on Reaction Rate02:55

Temperature Dependence on Reaction Rate

The Collision Theory
Atoms, molecules, or ions must collide before they can react with each other. Atoms must be close together to form chemical bonds. This premise is the basis for a theory that explains many observations regarding chemical kinetics, including factors affecting reaction rates.
The collision theory is based on the postulates that (i) the reaction rate is proportional to the rate of reactant collisions, (ii) the reacting species collide in an orientation allowing contact between...
Net Torque Calculations01:19

Net Torque Calculations

When a mechanic tries to remove a hex nut with a wrench, it is easier if the force is applied at the farthest end of the wrench handle. The lever arm is the distance from the pivot point (the hex nut in this case) to the person’s hand. If this distance is large, the torque is higher. Only the component of the force perpendicular to the lever arm contributes to the torque. Therefore, pushing the wrench perpendicular to the lever arm is more advantageous. If multiple people apply force to rotate...
Rolling Resistance01:21

Rolling Resistance

When a solid cylinder rolls steadily on a rigid surface, the normal force applied by the surface on the cylinder is perpendicular to the tangent at the contact point. However, since no materials are entirely rigid, the surface's reaction to the cylinder involves a range of normal pressures.
For instance, imagine a hard cylinder rolling on a comparatively soft surface. The cylinder's weight compresses the surface beneath it. As the cylinder moves, the material in front of it slows down due to...