Related Experiment Video

Updated: Jun 27, 2026

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes
06:34

Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

Published on: January 6, 2023

Experimental Study of Three AlSi10Mg Cellular Structures with Triply Periodic Minimal Surface (TPMS) Topology

Katarina Monkova1, Peter Pavol Monka1

  • 1Faculty of Manufacturing Technologies with a Seat in Presov, Technical University of Kosice, Sturova 31, 080 01 Presov, Slovakia.

Materials (Basel, Switzerland)
|June 26, 2026
PubMed

Keywords:
AlSi10MgSLM technologybendingcellular structuresfailurefracture surface

More Related Videos

Performing Microscope-Mounted Y-Shaped Cutting Tests06:15

Performing Microscope-Mounted Y-Shaped Cutting Tests

Published on: January 20, 2023

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle14:57

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle

Published on: January 30, 2019

Related Concept Videos

Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
Fatigue01:21

Fatigue

Fatigue occurs when materials rupture under repeated or fluctuating loads, even at stress levels far below their static breaking strength. It typically results in brittle failure, even for ductile materials. It is a critical consideration in designing machines and structural components subjected to repetitive or varying loads. The nature of these loadings can range from fluctuating loads like unbalanced pump impellers causing vibrations to repeatedly bending a thin steel rod wire back and forth...
Unsymmetric Loading of Thin-Walled Members01:23

Unsymmetric Loading of Thin-Walled Members

Thin-walled members with non-symmetrical cross-sections are vital to engineering structures, offering material efficiency and structural integrity. However, unsymmetrical loading on these members leads to complex stress distributions, resulting in simultaneous bending and twisting can cause deformation or structural failure. The interaction between bending and twisting requires detailed analysis to ensure structural resilience.
The concept of the shear center is crucial in countering the...
Bending of Material: Problem Solving01:09

Bending of Material: Problem Solving

In this lesson, determine the ratio of the maximum bending moments applied to two metal pipes, given that both pipes can withstand a maximum stress of 100 MPa. Both pipes have an outer radius of 1.8 cm. Pipe A has an inner radius of 1.5 cm, and Pipe B has an inner radius of 1 cm. The ratio of the maximum bending moment applied to two metallic pipes, each with a different inner and outer radius, is determined by considering their dimensions. The inner radius of the first pipe is 1.5 cm, and for...
Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
Eccentric Axial Loading in a Plane of Symmetry01:16

Eccentric Axial Loading in a Plane of Symmetry

Eccentric axial loading occurs when an axial load is applied away from the centroidal axis of a structural member. This scenario is common in engineering, where structural elements may not be directly aligned due to various design or functional requirements.