Related Experiment Video

Updated: Sep 22, 2026

A Low-Cost Method of Measuring the In Situ Primary Productivity of Periphyton Communities of Lentic Waters
06:02

A Low-Cost Method of Measuring the In Situ Primary Productivity of Periphyton Communities of Lentic Waters

Published on: December 16, 2022

[Effect and Mechanism of New Quality Productive Forces on Green Total Factor Productivity]

Peng Zhang1,2, Xiao-Yu Shi1,3, Li-Na Xin1

  • 1School of Land Engineering, Chang'an University, Xi'an 710054, China.

Huan Jing Ke Xue= Huanjing Kexue
|September 21, 2026
PubMed

Keywords:
green total factor productivityheterogeneitymediation effectnew quality productive forces（NQPF）threshold effect

More Related Videos

Visualization of Productivity Zones Based on Nitrogen Mass Balance Model in Narragansett Bay, Rhode Island05:04

Visualization of Productivity Zones Based on Nitrogen Mass Balance Model in Narragansett Bay, Rhode Island

Published on: July 14, 2023

High-Throughput, In-Field Screening of Photosynthetic Efficiency in Crop Plants Using an Autonomous Robot07:12

High-Throughput, In-Field Screening of Photosynthetic Efficiency in Crop Plants Using an Autonomous Robot

Published on: January 9, 2026

Related Concept Videos

Production Efficiency01:01

Production Efficiency

Net production efficiency (NPE) is the efficiency at which organisms assimilate energy into biomass for the next trophic level. Due to low metabolic rates and less energy spent on thermoregulatory processes, the NPE of ectotherms (cold-blooded animals) is 10 times higher than endotherms (warm-blooded animals).
Free Energy and Equilibrium02:56

Free Energy and Equilibrium

The free energy change for a process may be viewed as a measure of its driving force. A negative value for ΔG represents a driving force for the process in the forward direction, while a positive value represents a driving force for the process in the reverse direction. When ΔGrxn is zero, the forward and reverse driving forces are equal, and the process occurs in both directions at the same rate (the system is at equilibrium).
Recall that Q is the numerical value of the mass action expression...
Gibbs Free Energy and Thermodynamic Favorability02:23

Gibbs Free Energy and Thermodynamic Favorability

The spontaneity of a process depends upon the temperature of the system. Phase transitions, for example, will proceed spontaneously in one direction or the other depending upon the temperature of the substance in question. Likewise, some chemical reactions can also exhibit temperature-dependent spontaneities. To illustrate this concept, the equation relating free energy change to the enthalpy and entropy changes for the process is considered:
Free Energy and Equilibrium00:55

Free Energy and Equilibrium

The free energy change for a process may be viewed as a measure of its driving force. A negative value for ΔG represents a driving force for the process in the forward direction, while a positive value represents a driving force for the process in the reverse direction. When ΔG is zero, the forward and reverse driving forces are equal, and the process occurs in both directions at the same rate (the system is at equilibrium).
The reaction quotient, Q, is a convenient measure of the status of an...
Factors Affecting Activity Coefficient01:17

Factors Affecting Activity Coefficient

The extended Debye-Hückel equation indicates that the activity coefficient of an ion in an aqueous solution at 25°C depends on three partially interdependent properties: the ionic strength of the solution, the charge of the ion, and the ion size. 
The activity coefficient value for an ion is close to one when the solution has almost zero ionic strength, i.e., when the solution shows close to ideal behavior. As the ionic strength of the solution increases from 0 to 0.1 mol/L, a decrease in the...
Introduction to Partial Derivatives01:25

Introduction to Partial Derivatives

In many real-world situations, an output depends on more than one input. In a high-tech assembly plant, total production may depend on technician labor and machine capacity at the same time. This relationship can be represented by a continuous function P(T, M), where T denotes technician labor input, and M denotes machine capacity. When demand increases, but the budget remains fixed, the manager must determine which input will improve production more efficiently.Partial derivatives provide a...