Related Experiment Video

Updated: Oct 28, 2026

Visualization of Failure and the Associated Grain-Scale Mechanical Behavior of Granular Soils under Shear using Synchrotron X-Ray Micro-Tomography
09:00

Visualization of Failure and the Associated Grain-Scale Mechanical Behavior of Granular Soils under Shear using Synchrotron X-Ray Micro-Tomography

Published on: September 29, 2019

Topological Reconfiguration in Sheared Granular Assemblies: Non-Dissipative Mechanism and Its Irreversible

Xiaoxiao Wang1, Peng Li2, Pengqiang Yu1

  • 1Department of Civil Engineering, University of Science and Technology Beijing, Beijing 100083, China.

Materials (Basel, Switzerland)
|October 27, 2026
PubMed

Keywords:
elastic energy storage and releasegranular materialsirreversible free energymesoscopic loopstopological reconfiguration

More Related Videos

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

Measuring Material Microstructure Under Flow Using 1-2 Plane Flow-Small Angle Neutron Scattering09:08

Measuring Material Microstructure Under Flow Using 1-2 Plane Flow-Small Angle Neutron Scattering

Published on: February 6, 2014

Related Concept Videos

Reversible and Irreversible Processes01:14

Reversible and Irreversible Processes

The thermodynamic processes can be classified into reversible and irreversible processes. The processes that can be restored to their initial state are called reversible processes. It is only possible if the process is in quasi-static equilibrium, i.e., it takes place in infinitesimally small steps, and the system remains at equilibrium However, these are ideal processes and do not occur naturally. An ideal system undergoing a reversible process is always in thermodynamic equilibrium within...
Entropy Change in Reversible Processes01:10

Entropy Change in Reversible Processes

In the Carnot engine, which achieves the maximum efficiency between two reservoirs of fixed temperatures, the total change in entropy is zero. The observation can be generalized by considering any reversible cyclic process consisting of many Carnot cycles. Thus, it can be stated that the total entropy change of any ideal reversible cycle is zero.
The statement can be further generalized to prove that entropy is a state function. Take a cyclic process between any two points on a p-V diagram.
Shearing Strain01:20

Shearing Strain

The shearing strain represents a cubic element's angular change when subjected to shearing stress. This type of stress can transform a cube into an oblique parallelepiped without influencing normal strains. The cubic element experiences a significant transformation when exposed solely to shearing stress. Its shape alters from a perfect cube into a rhomboid, clearly demonstrating the effect of shearing strain. The degree of this strain is considered positive if it reduces the angle between the...
Plastic Deformation in Circular Shafts01:20

Plastic Deformation in Circular Shafts

When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and reloaded.
The Entropy as a State Function01:14

The Entropy as a State Function

Consider an arbitrary process that moves between two specific states (A and B) in a cyclic manner. This process is reversible and broken down into smaller parts that each follow a Carnot cycle. A Carnot cycle has two isothermal (constant temperature) processes. During these processes, the ratio of the amount of heat transferred to their respective temperature remains constant. The other two processes in the Carnot cycle are also reversible but adiabatic, which means they occur without any heat...