Related Experiment Video

Updated: Aug 19, 2026

Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis
08:08

Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis

Published on: May 8, 2014

Performance characteristics of total hip femoral components as a function of prosthesis modulus

M Manley, L Stern, J Gurtowski

    Bulletin of the Hospital for Joint Diseases Orthopaedic Institute
    |January 1, 1983
    PubMed

    More Related Videos

    A Probing Device for Quantitatively Measuring the Mechanical Properties of Soft Tissues during Arthroscopy06:16

    A Probing Device for Quantitatively Measuring the Mechanical Properties of Soft Tissues during Arthroscopy

    Published on: May 1, 2020

    Imaging of the Microstructural Failure Mechanism in the Human Hip08:43

    Imaging of the Microstructural Failure Mechanism in the Human Hip

    Published on: September 29, 2023

    Related Concept Videos

    Strain and Elastic Modulus01:15

    Strain and Elastic Modulus

    The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
    Hooke's Law01:26

    Hooke's Law

    Hooke's law, a pivotal principle in material science, establishes that the strain a material undergoes is directly proportional to the applied stress, defined by a factor called the modulus of elasticity or Young's modulus.
    Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

    Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

    Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
    Bending of Members Made of Several Materials01:11

    Bending of Members Made of Several Materials

    In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
    Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
    Elasticity in Concrete01:20

    Elasticity in Concrete

    Upon subjecting concrete to moderate or high uniaxial compressive or tensile stresses, the strain response is non-linear relative to the stress applied. As the stress is removed, the resulting stress-strain curve deviates from the original path traced during loading, creating a hysteresis loop, indicative of the concrete's non-linear and non-elastic properties. Typically, a material's modulus of elasticity, which is a measure of the material's stiffness, is inferred from the linear portion of...
    Dynamic Modulus of Elasticity of Concrete01:16

    Dynamic Modulus of Elasticity of Concrete

    The dynamic modulus of elasticity assesses how a concrete structure deforms under impact or dynamic loads. It is typically higher than the static modulus of elasticity, measured under slow, steady loading conditions.
    The sonic test is a common method to determine the dynamic modulus. In this test, a concrete beam, sized either 6 x 6 x 30 inches or 4 x 4 x 20 inches, is clamped at its center. Vibrations are initiated at one end of the beam by an electromagnetic exciter unit powered by a...