Related Experiment Video

Updated: Sep 23, 2026

Creating Rigidly Stabilized Fractures for Assessing Intramembranous Ossification, Distraction Osteogenesis, or Healing of Critical Sized Defects
07:35

Creating Rigidly Stabilized Fractures for Assessing Intramembranous Ossification, Distraction Osteogenesis, or Healing of Critical Sized Defects

Published on: April 11, 2012

Transient and residual stresses and displacements in self-curing bone cement - Part II: thermoelastic analysis of the

A M Ahmed, R Nair, D L Burke

    Journal of Biomechanical Engineering
    |February 1, 1982
    PubMed

    More Related Videos

    In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint07:09

    In situ Compressive Loading and Correlative Noninvasive Imaging of the Bone-periodontal Ligament-tooth Fibrous Joint

    Published on: March 7, 2014

    Adjustable Stiffness, External Fixator for the Rat Femur Osteotomy and Segmental Bone Defect Models10:09

    Adjustable Stiffness, External Fixator for the Rat Femur Osteotomy and Segmental Bone Defect Models

    Published on: October 9, 2014

    Related Concept Videos

    Temperature Dependent Deformation01:12

    Temperature Dependent Deformation

    In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added together...
    Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

    Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

    Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
    Residual Stresses01:26

    Residual Stresses

    Residual stresses reside in a structure even after removing the original stress inducer. This phenomenon often arises from varied plastic deformations across different parts of a structure. Consider a rod stretched beyond its yield point. It will not regain its original length due to permanent deformation. Even after load removal, the rod does not entirely lose stress because of uneven plastic deformations, resulting in residual stresses. The computation of these stresses in structures is...
    Residual Stresses in Circular Shafts01:10

    Residual Stresses in Circular Shafts

    In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the shaft's...
    Residual Stresses in Bending01:18

    Residual Stresses in Bending

    In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
    Stresses under Combined Loadings01:23

    Stresses under Combined Loadings

    When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
    The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...