Related Experiment Video

Updated: Aug 8, 2026

Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis
08:08

Oscillation and Reaction Board Techniques for Estimating Inertial Properties of a Below-knee Prosthesis

Published on: May 8, 2014

In-vivo elastic and damping response of the human leg to impact forces

J Mizrahi, Z Susak

    Journal of Biomechanical Engineering
    |February 1, 1982
    PubMed

    More Related Videos

    Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion09:32

    Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion

    Published on: April 11, 2018

    Experimental Methods to Study Human Postural Control08:12

    Experimental Methods to Study Human Postural Control

    Published on: September 11, 2019

    Related Concept Videos

    Indeterminate Structure01:18

    Indeterminate Structure

    Indeterminate structures refer to structures where internal forces and reactions cannot be determined using only the equations of static equilibrium.  Indeterminate structures have more unknown forces and reaction forces than equations of static equilibrium that can be used to determine them. Indeterminate structures are often used in engineering to create complex, efficient, and aesthetically pleasing structures. There are various types of indeterminate structures used in engineering and some...
    Muscles of the Leg that Move the Foot and Toes01:28

    Muscles of the Leg that Move the Foot and Toes

    The human leg comprises an intricate system of muscles that facilitate the movement of feet and toes. Within this system, the muscles are categorized into the anterior, lateral, and posterior compartments, each with a unique set of muscles carrying out specific functions.
    Anterior Compartment
    The anterior compartment includes muscles that contribute to the dorsiflexion of the foot. This compartment houses the tibialis anterior, extensor hallucis longus, and extensor digitorum longus muscles.
    Members Made of Elastoplastic Material01:19

    Members Made of Elastoplastic Material

    The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
    As the bending moment...
    Residual Stresses in Bending01:18

    Residual Stresses in Bending

    In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
    Impact Loading01:19

    Impact Loading

    Impact loading occurs when a moving object collides with a stationary structure, such as a rod with a uniform cross-sectional area fixed at one end. Under these conditions, the rod absorbs the kinetic energy from the striking object, leading to deformation and subsequent stress development. As the rod returns to its original position and reaches maximum stress, the absorbed energy, initially manifested as kinetic energy, transforms entirely into strain energy.
    In cases of elastic deformation,...
    Dynamic Modulus of Elasticity of Concrete01:16

    Dynamic Modulus of Elasticity of Concrete

    The dynamic modulus of elasticity assesses how a concrete structure deforms under impact or dynamic loads. It is typically higher than the static modulus of elasticity, measured under slow, steady loading conditions.
    The sonic test is a common method to determine the dynamic modulus. In this test, a concrete beam, sized either 6 x 6 x 30 inches or 4 x 4 x 20 inches, is clamped at its center. Vibrations are initiated at one end of the beam by an electromagnetic exciter unit powered by a...