Jove
Visualize
Contact Us
JoVE
x logofacebook logolinkedin logoyoutube logo
ABOUT JoVE
OverviewLeadershipBlogJoVE Help Center
AUTHORS
Publishing ProcessEditorial BoardScope & PoliciesPeer ReviewFAQSubmit
LIBRARIANS
TestimonialsSubscriptionsAccessResourcesLibrary Advisory BoardFAQ
RESEARCH
JoVE JournalMethods CollectionsJoVE Encyclopedia of ExperimentsArchive
EDUCATION
JoVE CoreJoVE BusinessJoVE Science EducationJoVE Lab ManualFaculty Resource CenterFaculty Site
Terms & Conditions of Use
Privacy Policy
Policies

Filters

Lisa-Maria Wittmann
Dietmar Drummer

Polymers

Showing results (1-10 of 48) with videos related to

Pageof 5
Sort By:
Polymers|April 23, 2022
Two Layer Sheets for Processing Post-Consumer MaterialsLisa-Maria Wittmann, Dietmar Drummer
Polymers|August 12, 2022
Biaxial Elongation Behavior in Partially Molted State of Two-Layer Sheets Containing Postconsumer MaterialLisa-Maria Wittmann, Joachim Kaschta, Dietmar Drummer
Polymers|October 14, 2023
Investigating the Integration of Nonwoven Carbon Fibers for Mechanical Enhancement in Compression Molded Fiber-Reinforced Polymer Bipolar PlatesRainer Frank, Lisa-Maria Wittmann, Tobias Kleffel, et al.
Polymers|February 26, 2022
Analysis of UV Curing Strategy on Reaction Heat Control and Part Accuracy for Additive ManufacturingFengze Jiang, Dietmar Drummer
Polymers|April 13, 2023
Test Rig for the In Situ Measurement of the Elastic Tooth Deflection of Plastic GearsChristoph Herzog, Dietmar Drummer
Polymers|August 12, 2022
Filling Behavior in Joining Using Pin-like StructuresMichael Wolf, Dietmar Drummer
Polymers|January 10, 2026
Improving the Thermal Conductivity by Varying the Filler Geometry of Copper in ThermosetsUta Rösel, Dietmar Drummer
Polymers|July 24, 2021
Pressure Equilibrium Time of a Cyclic-Olefin CopolymerBenedikt Roth, Dietmar Drummer
Polymers|October 26, 2024
Influence of Different Filler Systems on the Thermal Conductivity and Mechanical Properties of ThermosetsUta Rösel, Dietmar Drummer
Polymers|September 28, 2023
Limitations of the Check Calculation for Tooth Deformation of Plastic Gears According to Gear Design Guideline VDI 2736Christoph Herzog, Dietmar Drummer
Pageof 5

Showing results (1-10 of 48) with videos related to

Sort By:
Pageof 5
Polymers|April 23, 2022
Two Layer Sheets for Processing Post-Consumer MaterialsLisa-Maria Wittmann, Dietmar Drummer
Polymers|August 12, 2022
Biaxial Elongation Behavior in Partially Molted State of Two-Layer Sheets Containing Postconsumer MaterialLisa-Maria Wittmann, Joachim Kaschta, Dietmar Drummer
Polymers|October 14, 2023
Investigating the Integration of Nonwoven Carbon Fibers for Mechanical Enhancement in Compression Molded Fiber-Reinforced Polymer Bipolar PlatesRainer Frank, Lisa-Maria Wittmann, Tobias Kleffel, et al.
Polymers|February 26, 2022
Analysis of UV Curing Strategy on Reaction Heat Control and Part Accuracy for Additive ManufacturingFengze Jiang, Dietmar Drummer
Polymers|April 13, 2023
Test Rig for the In Situ Measurement of the Elastic Tooth Deflection of Plastic GearsChristoph Herzog, Dietmar Drummer
Polymers|August 12, 2022
Filling Behavior in Joining Using Pin-like StructuresMichael Wolf, Dietmar Drummer
Polymers|January 10, 2026
Improving the Thermal Conductivity by Varying the Filler Geometry of Copper in ThermosetsUta Rösel, Dietmar Drummer
Polymers|July 24, 2021
Pressure Equilibrium Time of a Cyclic-Olefin CopolymerBenedikt Roth, Dietmar Drummer
Polymers|October 26, 2024
Influence of Different Filler Systems on the Thermal Conductivity and Mechanical Properties of ThermosetsUta Rösel, Dietmar Drummer
Polymers|September 28, 2023
Limitations of the Check Calculation for Tooth Deformation of Plastic Gears According to Gear Design Guideline VDI 2736Christoph Herzog, Dietmar Drummer
Pageof 5