Video Experimental Relacionado

Updated: Jul 18, 2026

Process of Making Three-dimensional Microstructures using Vaporization of a Sacrificial Component
08:31

Process of Making Three-dimensional Microstructures using Vaporization of a Sacrificial Component

Published on: November 2, 2013

Formación y subdivisión de estructuras de deformación durante la deformación plástica

Bo Jakobsen1, Henning F Poulsen, Ulrich Lienert

  • 1Center for Fundamental Research: Metal Structures in Four Dimensions, Materials Research Department, Risø National Laboratory, DK-4000 Roskilde, Denmark.

Science (New York, N.Y.)
|May 13, 2006
PubMed
Resumen

Nuevos métodos de difracción de rayos X revelan el comportamiento dinámico de las estructuras de dislocación durante la deformación del metal. Estos hallazgos ofrecen información sobre la resistencia de los materiales y los procesos de endurecimiento del trabajo.

Más Videos Relacionados

Fabrication of a Bioactive, PCL-based "Self-fitting" Shape Memory Polymer Scaffold09:37

Fabrication of a Bioactive, PCL-based "Self-fitting" Shape Memory Polymer Scaffold

Published on: October 23, 2015

3D Printing and In Situ Surface Modification via Type I Photoinitiated Reversible Addition-Fragmentation Chain Transfer Polymerization07:28

3D Printing and In Situ Surface Modification via Type I Photoinitiated Reversible Addition-Fragmentation Chain Transfer Polymerization

Published on: February 18, 2022

Videos de Conceptos Relacionados

Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and reloaded.
Bending of Members Made of Several Materials01:11

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
Plastic Deformations of Members with a Single Plane of Symmetry01:21

Plastic Deformations of Members with a Single Plane of Symmetry

When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their original...
Transformation of Plane Strain01:12

Transformation of Plane Strain

When analyzing elongated structures like bars subjected to uniformly distributed loads, it is essential to understand the transformation of plane strain when coordinate axes are rotated. This transformation helps to assess how material deformation characteristics vary with orientation, which is crucial in materials science and structural engineering.
Under plane strain conditions, typical for members where one dimension significantly exceeds the others, deformations and resultant strains are...