Video Experimental Relacionado

Updated: Jan 8, 2026

Coordinate Mapping of Hyolaryngeal Mechanics in Swallowing
14:13

Coordinate Mapping of Hyolaryngeal Mechanics in Swallowing

Published on: May 6, 2014

18.7K

Introducción del Ángulo de Cobb Modificado para Medir la Curvatura de la Columna Cervical Durante la Deglución

Catriona M Steele1,2,3, Makaya O' Grady4, Sima Farpour4

  • 1KITE Research Institute - University Health Network Toronto Canada.

Laryngoscope investigative otolaryngology
|December 22, 2025
PubMed
Resumen

El ángulo de Cobb modificado revisado (MCA) C2-C4 ofrece una mayor confiabilidad y validez para medir la curvatura de la columna cervical durante la deglución. Este método revisado mejora la precisión en la investigación de la deglución en comparación con el MCA original.

Palabras clave:
columna cervicalvértebras cervicalesdegluciónalineación de cabeza y cuellotragar

Más Videos Relacionados

Measurement of Dynamic Scapular Kinematics Using an Acromion Marker Cluster to Minimize Skin Movement Artifact10:07

Measurement of Dynamic Scapular Kinematics Using an Acromion Marker Cluster to Minimize Skin Movement Artifact

Published on: February 10, 2015

19.9K
Assessment of Static Graviceptive Perception in the Roll-Plane using the Subjective Visual Vertical Paradigm06:30

Assessment of Static Graviceptive Perception in the Roll-Plane using the Subjective Visual Vertical Paradigm

Published on: April 28, 2020

6.1K

Videos de Conceptos Relacionados

Unsymmetric Bending - Angle of Neutral Axis01:15

Unsymmetric Bending - Angle of Neutral Axis

Unsymmetrical bending occurs when a structural member is subjected to bending moments in a plane that does not align with the member's principal axes. This scenario typically arises in beams and other structural components when loads are applied at non-ideal angles, introducing complexities in stress analysis.
When a bending moment is applied at an angle θ concerning the vertical axis of a symmetrical member, it can be resolved into components along the member's principal...
797
Angle of Twist - Elastic Range01:13

Angle of Twist - Elastic Range

Consider a cylindrical shaft with a length denoted by L and a consistent cross-sectional radius referred to as r. This shaft undergoes a torque at the free end. The highest shearing strain within the shaft is directly proportional to the twist angle and the radial distance from the shaft axis. When the shaft behaves elastically, this shearing strain can be articulated using variables such as the applied torque, radial distance, the polar moment of inertia, and the modulus of rigidity. By...
725
Vertebral Column: Regions and Curvature01:16

Vertebral Column: Regions and Curvature

The vertebral column or spine is a flexible column that supports the head, neck, and body and  allows for their movements. It also protects the spinal cord.
Regions of the Vertebral Column
In an adult, the spine is subdivided into five regions: the cervical, the thoracic, the lumbar, the sacral, and the coccygeal region. The spine initially develops as a series of 33 vertebrae; after 20 years of age, the nine bones in the sacral region, five sacral, and four coccygeal bones fuse to form...
5.8K
Adjusting a Traverse01:12

Adjusting a Traverse

In the site survey of a four-sided traverse, internal angles are essential to ensure geometric accuracy. The survey revealed that the sum of the measured internal angles was 359 degrees and 48 minutes, which is 12 minutes less than the expected 360 degrees. This discrepancy signals an error likely arising from measurement inaccuracies during the fieldwork.To rectify this error, the adjustment process involved distributing the 12-minute shortfall equally across the four internal angles. By...
342
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the torque...
728
Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member...
469