Video Experimental Relacionado

Updated: Feb 21, 2026

Studying Large Amplitude Oscillatory Shear Response of Soft Materials
06:07

Studying Large Amplitude Oscillatory Shear Response of Soft Materials

Published on: April 25, 2019

13.8K

Influencia del efecto Kerr en las propiedades de las estructuras simétricas PT no lineales

Piotr Witoński, Agnieszka Mossakowska-Wyszyńska, Paweł Szczepański

    Optics express
    |February 20, 2026
    PubMed
    Resumen

    El efecto Kerr altera significativamente las intensidades de salida en estructuras simétricas PT, modificando las características y eliminando potencialmente la biestabilidad causada por la saturación de ganancia / pérdida.

    Más Videos Relacionados

    Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes06:34

    Finite Element Modeling for the Simulation of the Quasi-Static Compression of Corrugated Tapered Tubes

    Published on: January 6, 2023

    3.3K
    A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials11:28

    A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials

    Published on: May 18, 2015

    13.0K

    Videos de Conceptos Relacionados

    Bending of Members Made of Several Materials01:11

    Bending of Members Made of Several Materials

    In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
    Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
    639
    Plastic Deformations of Members with a Single Plane of Symmetry01:21

    Plastic Deformations of Members with a Single Plane of Symmetry

    When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
    388
    Torsion of Noncircular Members01:16

    Torsion of Noncircular Members

    Circular shafts undergoing torsional stress maintain their cross-sectional integrity due to their axisymmetric nature. This symmetry ensures an even distribution of stress, allowing the shaft to withstand torsion without distorting. In contrast, square bars, lacking this axial symmetry, experience significant distortion across their cross-sections when subjected to torsion, with the exception of along their diagonals and at lines connecting midpoints. A detailed examination of a cubic element...
    634
    Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

    Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

    Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
    635
    General Case of Eccentric Axial Loading01:12

    General Case of Eccentric Axial Loading

    Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from symmetrical bending, which are essential for designing structures to withstand different loading conditions.
    Consider a member subjected to equal and opposite forces that are applied along a line that does not coincide with the member's neutral axis. In unsymmetrical...
    540
    Members Made of Elastoplastic Material01:19

    Members Made of Elastoplastic Material

    The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
    As the bending moment...
    429