関連する実験動画

Updated: Jul 11, 2026

Atom Probe Tomography Analysis of Exsolved Mineral Phases
08:14

Atom Probe Tomography Analysis of Exsolved Mineral Phases

Published on: October 25, 2019

聖ペトロと聖パウロの岩:高温で,マントル由来の侵入

W G Melson, E Jarosewich, V T Bowen

    Science (New York, N.Y.)
    |March 24, 1967
    PubMed
    まとめ

    セントポールズ・ロックには,これまで知られていたよりも多くの種類の岩石が発見されています. これらの岩は,熱い固体侵入の中で組み込まれ,変化する前に,マントルの様々な深さで形成された可能性が高い.

    さらに関連する動画

    Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System10:52

    Conducting Elevated Temperature Normal and Combined Pressure-Shear Plate Impact Experiments Via a Breech-end Sabot Heater System

    Published on: August 7, 2018

    Metal-silicate Partitioning at High Pressure and Temperature: Experimental Methods and a Protocol to Suppress Highly Siderophile Element Inclusions11:50

    Metal-silicate Partitioning at High Pressure and Temperature: Experimental Methods and a Protocol to Suppress Highly Siderophile Element Inclusions

    Published on: June 13, 2015

    関連する概念動画

    Isothermal Processes01:21

    Isothermal Processes

    A thermodynamic process that occurs at constant temperature is called an isothermal process. Heat slowly flows into the system or out of the system to maintain thermal equilibrium. Processes involving phase changes like water evaporation into steam or freezing water into ice at a constant temperature are examples of Isothermal Processes.
    An ideal gas can also undergo isothermal expansion or compression.
    For example, consider 1 mole of an ideal gas inside an isolated cylinder at initial volume V...
    Thermal Strain01:19

    Thermal Strain

    Thermal strain is a concept that arises when we consider how temperature changes affect structures. Unlike the conventional assumption that structures remain constant under load, real-world scenarios often involve temperature fluctuations that can significantly impact these structures. Consider a homogeneous rod with a uniform cross-section resting freely on a flat horizontal surface. If the rod's temperature increases, the rod elongates. This elongation is proportional to the temperature...
    Temperature Dependent Deformation01:12

    Temperature Dependent Deformation

    In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added together...
    Thermal Sigmatropic Reactions: Overview01:16

    Thermal Sigmatropic Reactions: Overview

    Sigmatropic rearrangements are a class of pericyclic reactions in which a σ bond migrates from one part of a π system to another. These are intramolecular rearrangements where the total number of σ and π bonds remain unchanged.
    Sigmatropic shifts are classified based on an order term [i, j ], where i and j indicate the number of atoms across which each end of the σ bond migrates. Below are examples of a [3,3] sigmatropic shift in 1,5-hexadiene, referred to as...
    Atomic Spectroscopy: Effects of Temperature01:27

    Atomic Spectroscopy: Effects of Temperature

    Atomization, converting samples into gas-phase atoms and ions, is essential for atomic spectroscopy. The flame temperature required for atomization affects the efficiency of the atomic spectroscopic methods by increasing the atomization efficiency and the relative population of the excited and ground states.
    At thermal equilibrium, the relative populations of excited and ground state atoms can be estimated using the Maxwell–Boltzmann distribution. For example, an increase in temperature from...
    Thermal Stress01:09

    Thermal Stress

    If the temperature of an object is changed while it is prevented from expanding or contracting, the object is subjected to stress. The stress is compressive if the object expands in the absence of constraint and tensile if it contracts. This stress resulting from temperature change is known as thermal stress. It can be quite large and can cause damage. To avoid this stress, engineers may design components so they can expand and contract freely. For instance, on highways, gaps are deliberately...