関連する実験動画

Updated: Jul 11, 2026

Proofreading and DNA Repair Assay Using Single Nucleotide Extension and MALDI-TOF Mass Spectrometry Analysis
11:08

Proofreading and DNA Repair Assay Using Single Nucleotide Extension and MALDI-TOF Mass Spectrometry Analysis

Published on: June 19, 2018

訂正と明確化について

    Science (New York, N.Y.)
    |December 23, 1994
    PubMed
    まとめ

    この研究は,オルファクトリーサイクルヌクレオチドゲートカチオンチャネルに関する研究における数字とテキストを訂正し,オルファクトリーシグナル伝達におけるカルシウム-カルモジュリン調節の役割を明確にします.

    さらに関連する動画

    Correction of Presbyopia by Monocular Bi-Aspheric Ablation Profile05:46

    Correction of Presbyopia by Monocular Bi-Aspheric Ablation Profile

    Published on: September 20, 2024

    Scanning Skeletal Remains for Bone Mineral Density in Forensic Contexts07:56

    Scanning Skeletal Remains for Bone Mineral Density in Forensic Contexts

    Published on: January 29, 2018

    関連する概念動画

    Distance Corrections01:15

    Distance Corrections

    To achieve precise distance measurements, especially in surveying and construction, certain corrections must be applied to account for potential sources of error like the standardization errors, temperature variations, and slope adjustments.Standardization error emerges when measurement equipment undergoes changes, such as wear, repairs, or weather impacts. To address this, surveyors compare the equipment’s readings to a standard. This process identifies any deviation that might lead to...
    NMR Spectrometers: Resolution and Error Correction01:14

    NMR Spectrometers: Resolution and Error Correction

    When magnetic nuclei in a sample achieve resonance and undergo relaxation, the signal detected in NMR is an approximately exponential free induction decay. Fourier transform of an exponential decay yields a Lorentzian peak in the frequency domain. Lorentzian peaks in an NMR spectrum are defined by their amplitude, full width at half maximum, and position, where the peak width is governed by the spin-spin relaxation time alone. In real experiments, however, the applied magnetic field is rendered...
    Accuracy, limits, and approximation01:28

    Accuracy, limits, and approximation

    Accuracy, limits, and approximations are common in many fields, especially in engineering calculations. These concepts are imperative for ensuring that a given value is as close as possible to its true value.
    Accuracy is defined as the closeness of the measured value to the true or actual value. In engineering mechanics, repeated measurements are taken during theoretical or experimental analyses to ensure that the result is precise and accurate.
    The accuracy of any solution is based on the...
    Types of Errors: Detection and Minimization01:12

    Types of Errors: Detection and Minimization

    Error is the deviation of the obtained result from the true, expected value or the estimated central value. Errors are expressed in absolute or relative terms.
    Absolute error in a measurement is the numerical difference from the true or central value. Relative error is the ratio between absolute error and the true or central value, expressed as a percentage.
    Errors can be classified by source, magnitude, and sign. There are three types of errors: systematic, random, and gross.
    Systematic or...
    Contaminants and Errors01:16

    Contaminants and Errors

    Effective sample preparation is crucial for accurate and reliable laboratory analysis. During this process, two significant sources of error can arise: concentration bias from improper sample splitting and contamination caused by methods used to reduce particle size, such as grinding or homogenization. Identifying and minimizing these potential errors is crucial to ensuring the validity of the analysis.
    Another key consideration is determining the appropriate number of samples required to...
    Errors and Mistakes in Surveying01:19

    Errors and Mistakes in Surveying

    Errors and mistakes in surveying refer to inaccuracies in measurements and data recording. The errors are deviations from the actual value caused by human sensory limitations, equipment flaws, or environmental effects. These errors are typically unintentional and can result from the inherent imperfections in the instruments used, atmospheric conditions, or the observer’s inability to perceive exact measurements. On the other hand, mistakes are caused by the surveyor's lack of attention,...