関連する実験動画

Updated: Sep 10, 2025

The Trier Social Stress Test Protocol for Inducing Psychological Stress
09:39

The Trier Social Stress Test Protocol for Inducing Psychological Stress

Published on: October 19, 2011

56.7K

どれだけの時間が 長いのか? 人とエレベーターの相互作用における待ち時間とストレスの検討

Masahiro Shiomi1, Masayuki Kakio2, Takahiro Miyashita1

  • 1Advanced Telecommunications Research Institute International, Seika, Kyoto, Japan.

PeerJ
|August 25, 2025
PubMed
まとめ

エレベーターの待ち時間は ユーザーのストレスに影響します この研究は実際の待ち時間と 予想される待ち時間の違いを明らかにし エレベーターの体験を改善するための洞察を提供します

キーワード:
エレベーター人間の行動ストレス待機時間

さらに関連する動画

Enactive Phenomenological Approach to the Trier Social Stress Test: A Mixed Methods Point of View05:26

Enactive Phenomenological Approach to the Trier Social Stress Test: A Mixed Methods Point of View

Published on: January 7, 2019

6.8K
Assessing the Autonomic and Behavioral Effects of Passive Motion in Rats using Elevator Vertical Motion and Ferris-Wheel Rotation06:18

Assessing the Autonomic and Behavioral Effects of Passive Motion in Rats using Elevator Vertical Motion and Ferris-Wheel Rotation

Published on: February 7, 2020

7.6K

関連する概念動画

Psychological Responses to Stress01:20

Psychological Responses to Stress

Psychological responses to stress encompass the various cognitive and emotional reactions individuals experience when faced with challenging or threatening situations, such as a job loss. Prolonged exposure to stressors can disturb emotional balance, increasing negative emotions (e.g., anxiety and sadness) and diminishing positive emotions (e.g., joy and satisfaction). These persistent emotional shifts are associated with an increased risk of both physical illness and mental health issues, such...
99
Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes....
376
Applications of Stress01:04

Applications of Stress

Consider a structure made of a boom and a rod designed to support a load. These two components are connected by a pin and stabilized by brackets and pins. The boom and the rod are detached from their supports to assess the different stresses imposed on this structure, and a free-body diagram is drawn. Then, all the forces applied, including the load acting on the structure, are identified. The reaction forces exerted on both the boom and the rod are computed using the equilibrium equations.
The...
400
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
233
Principal Stresses: Problem Solving01:15

Principal Stresses: Problem Solving

When analyzing two planes intersecting at right angles under the influence of shearing, tensile, and compressive stresses, it is essential to identify principal planes, maximum shearing stress, and principal stresses. To find the principal planes, apply a formula that equates them to twice the shearing stress divided by the difference between tensile and compressive stresses.
304
Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
227