関連する実験動画

Updated: Feb 22, 2026

Environmental Dynamic Mechanical Analysis to Predict the Softening Behavior of Neural Implants
06:59

Environmental Dynamic Mechanical Analysis to Predict the Softening Behavior of Neural Implants

Published on: March 1, 2019

8.4K

保存条件がマキシル間弾性材の機械的性質に及ぼす影響

Wanda Urbanova1,2,3,4, Iva Voborná5,6, Tereza Šrolerová7

  • 1Department of Stomatology 3rd Faculty of Medicine Charles University and University Hospital Královské Vinohrady, Prague, Czech Republic.

Progress in orthodontics
|February 20, 2026
PubMed
まとめ

光への曝露は,ラテックスの間弾性 (IE) 力を著しく低下させ,特に散らばった状態で保管する場合に起きます. 室温の防光箱にIEを保存すると,その強さが保存され,矯正治療の有効性を維持するための重要な患者ガイドラインが提供されます.

キーワード:
フォースフォースフォースフォースフォースフォース熱への曝露は,熱による曝露である.インターマキシラー弾性棒光への曝露 光への曝露 光への曝露 光への曝露保存条件 保存条件について

さらに関連する動画

Biological Preparation and Mechanical Technique for Determining Viscoelastic Properties of Zonular Fibers06:39

Biological Preparation and Mechanical Technique for Determining Viscoelastic Properties of Zonular Fibers

Published on: December 16, 2021

2.4K
Environmentally-controlled Microtensile Testing of Mechanically-adaptive Polymer Nanocomposites for ex vivo Characterization11:38

Environmentally-controlled Microtensile Testing of Mechanically-adaptive Polymer Nanocomposites for ex vivo Characterization

Published on: August 20, 2013

10.7K

関連する概念動画

Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
430
Plastic Behavior01:21

Plastic Behavior

A material's elastic behavior is characterized by the disappearance of stress once the load is removed, allowing the material to return to its original state. However, when stress surpasses the yield point, yielding commences, marking the onset of plastic deformation or permanent set. This change from elastic to plastic behavior is influenced by the peak stress value and the duration before the load is removed. An intriguing observation occurs when a specimen is loaded, unloaded, and...
625
Hooke's Law01:26

Hooke's Law

Hooke's law, a pivotal principle in material science, establishes that the strain a material undergoes is directly proportional to the applied stress, defined by a factor called the modulus of elasticity or Young's modulus.
1.7K
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
639
Strain and Elastic Modulus01:15

Strain and Elastic Modulus

The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
9.2K
Circular Shafts - Elastoplastic Materials01:24

Circular Shafts - Elastoplastic Materials

The study of solid circular shafts under stress shows that within the elastic limit, stress increases directly to the distance from the shaft's center. This relationship holds until the shaft reaches a critical point of stress, beyond which it begins to yield, marking the transition from elastic to plastic deformation. At this crucial juncture, the maximum torque the shaft can endure without permanent deformation is determined, signifying the limit of its elastic behavior.
As torque on the...
515