相关实验视频

Updated: Jul 25, 2025

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters
15:25

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

Published on: February 4, 2018

6.2K

双带和宽带带宽带过渡过器使用合线和三级阻抗塞

Abdullah J Alazemi1

  • 1Electrical Engineering Department, College of Engineering and Petroleum, Kuwait University, Safat, Kuwait City 13060, Kuwait.

Micromachines
|June 28, 2023
PubMed
概括

这项研究介绍了使用合线和三级阻抗断片的新型双带和宽带带宽带过器. 过器在GSM和GPS等应用中表现出有效的性能,通过实验结果验证了理论设计.

关键词:
带通波器的波器是一个带通波器.连接线连接线的线路双频带的双频带.三级阻抗断片的三级阻抗断片.宽带宽带是什么意思

更多相关视频

Generation and Coherent Control of Pulsed Quantum Frequency Combs06:42

Generation and Coherent Control of Pulsed Quantum Frequency Combs

Published on: June 8, 2018

9.0K
X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells00:10

X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells

Published on: August 20, 2019

13.9K

相关概念视频

Passive Filters01:27

Passive Filters

Passive filters are utilized to shape the frequency spectrum of signals across a diverse array of applications. These filters, using only passive elements like resistors (R), inductors (L), and capacitors (C), are capable of selectively allowing or blocking certain frequency ranges without the need for external power sources.
Low-Pass Filters
Low-pass filters are designed to transmit signals with frequencies lower than the cutoff frequency, ωc, and attenuate those above it. The cutoff...
562
Active Filters01:25

Active Filters

Active filters are electronic circuits that use operational amplifiers (op-amps), resistors, and capacitors to filter out unwanted frequency components from a signal. A first-order low-pass active filter is designed to pass signals with a frequency lower than a certain cutoff frequency and attenuate frequencies higher than that cutoff frequency. The transfer function for a first-order low-pass active filter is:
864
Design Example01:23

Design Example

The innovation of touch-tone telephony revolutionized the telecommunications industry by replacing the traditional rotary dial with a dual-tone multi-frequency (DTMF) signaling system. This system uses a matrix-style keypad with buttons arranged in four rows and three columns, creating 12 distinct signals each assigned to a pair of frequencies. Each button press results in a simultaneous generation of two sinusoidal tones – one from a low-frequency group (697 to 941 Hz) and one from a...
348
Bandpass Sampling01:17

Bandpass Sampling

In signal processing, bandpass sampling is an effective technique for sampling signals that have most of their energy concentrated within a narrow frequency band. This type of signal is known as a bandpass signal. The key principle of bandpass sampling involves sampling the signal at a rate that is greater than twice the signal's bandwidth to prevent aliasing.
A bandpass signal has a spectrum with a lower frequency limit, denoted as ω1, and an upper frequency limit, denoted as ω2....
211
Transmission Line Design Considerations01:23

Transmission Line Design Considerations

Aluminum has become the material of choice for overhead transmission lines, surpassing copper due to its abundance and cost-effectiveness. The most prevalent type is the aluminum conductor, steel-reinforced (ACSR), which combines aluminum strands around a steel core. Other variants include all-aluminum conductors (AAC), all-aluminum alloy conductors (AAAC), aluminum conductor alloy-reinforced (ACAR), and aluminum-clad steel conductors. Advanced designs, such as aluminum conductors with steel...
177
Parallel Resonance01:23

Parallel Resonance

The parallel RLC circuit is an arrangement where the resistor (R), inductor (L), and capacitor (C) are all connected to the same nodes and, as a result, share the same voltage across them. The parallel RLC circuit is analyzed in terms of admittance (Y), which reflects the ease with which current can flow. The admittance is given by:
233