相关实验视频

Updated: Jul 17, 2025

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material
07:42

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Published on: December 20, 2024

421

批量填充树脂基复合材料和三种接材料在玻璃纤维增强柱子的固上进行比较

Carlos Alberto Kenji Shimokawa1, Paula Mendes Acatauassú Carneiro2, Tamile Rocha da Silva Lobo1

  • 1Department of Restorative Dentistry, School of Dentistry, University of São Paulo, São Paulo, SP, Brazil.

Restorative dentistry & endodontics
|September 7, 2023
PubMed
概括

与传统水泥相比,可流式散装填充复合材料 (BF) 显示出与传统水泥相比,可比或更高的推出键强度和微硬度用于接玻璃纤维柱子. 当足够的光固化可以实现时,这种材料是一种可行的选择.

关键词:
债券的强度 债券的强度 债券的强度硬度测试 硬度测试 硬度测试基于树脂的水泥是基于树脂的水泥基于树脂的复合材料.

更多相关视频

Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation08:45

Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation

Published on: July 21, 2014

13.5K
Roughness Impact of Piezoelectric Dental Scaler on Two Distinct Flowable Composite Filling Materials05:30

Roughness Impact of Piezoelectric Dental Scaler on Two Distinct Flowable Composite Filling Materials

Published on: January 10, 2025

663

相关概念视频

Fiber Reinforced Concrete01:22

Fiber Reinforced Concrete

Fiber-reinforced concrete significantly enhances the structural and nonstructural properties of traditional concrete by incorporating fibers like steel, glass, and polymers. These fibers, varying from natural ones such as sisal and cellulose to manufactured ones like polypropylene and Kevlar, are mixed into hydraulic cement with aggregates. Steel fibers, often preferred for their robustness, contribute to improved ductility, toughness, and post-cracking performance. The concrete is classified...
102
Strength of Cement01:20

Strength of Cement

Strength tests for cement are not performed directly on neat cement paste due to difficulty in obtaining consistent, reliable specimens. Instead, cement is typically tested in the form of cement-sand mortar.
For compressive strength tests, ASTM C 109-05 standards prescribe a cement-sand mix ratio of 1:2.75 and a water/cement ratio of 0.485 for making 2-inch cubes. These cubes are mixed, cast, and cured in saturated lime water at 23°C until testing. Flexural strength testing, outlined in...
166
Porosity in Cement Paste01:18

Porosity in Cement Paste

The porosity of concrete is a measure of the void spaces within its structure. These spaces impact its strength and durability significantly. When water and cement interact, a chemical reaction called hydration creates a semi-solid paste. This paste includes combined water, making up approximately 23% of the cement's dry mass, and gel water, which fills minuscule voids known as gel pores, accounting for about 28% of the cement gel volume.
The balance of water to cement in the mix is...
170
Ferrocement01:30

Ferrocement

Ferro-cement is a distinctive construction material that represents an innovative variant of reinforced concrete, characterized by its unique composition and the method by which it is formed. Unlike standard reinforced concrete, which relies on larger steel bars for reinforcement, ferro-cement utilizes densely packed layers of mesh or fine rods, fully encased in cement mortar. This composition allows for the creation of structures that are significantly thinner and more flexible than their...
212
Additives and Fillers in Concrete01:29

Additives and Fillers in Concrete

Additives and fillers are integral to enhancing the properties of concrete. Pozzolans and blast-furnace slag are additives or admixtures due to their reactions with calcium hydroxide released during cement hydration. Fillers, which are finely ground and similar in fineness to Portland cement, improve concrete attributes such as workability density, and reduce capillary bleeding or cracking. Some fillers possess hydraulic properties or participate in benign reactions within the cement paste.
The...
115