相关实验视频

Updated: Jul 16, 2025

Experimental Procedure for Warm Spinning of Cast Aluminum Components
07:36

Experimental Procedure for Warm Spinning of Cast Aluminum Components

Published on: February 1, 2017

9.5K

四种热处理的反转仪器的特征:设计,金,机械性能和灌流动模式

Jorge N R Martins1,2,3,4, Emmanuel João Nogueira Leal Silva5,6, Duarte Marques1,2,3,4,7

  • 1Faculdade de Medicina Dentária, Universidade de Lisboa, Lisboa, Portugal.

International endodontic journal
|September 12, 2023
PubMed
概括

这项研究比较了四个经过热处理的反转仪器,发现了设计和机械性能的变化,但在模拟的根管灌流量上没有显著差异. 这些发现有助于选择合适的内牙仪器.

关键词:
3D表面扫描扫描 3D表面扫描计算流体动力学的流体动力学.不同扫描热量计差异扫描热量计.牙周内科 牙周内科是指牙周内科.额外口腔扫描仪扫描仪互惠的工具是互惠的工具.骨强度是指骨的强度.

更多相关视频

Author Spotlight: Simulation and Analysis of the Temperature Rise of Ring Main Unit Equipment04:35

Author Spotlight: Simulation and Analysis of the Temperature Rise of Ring Main Unit Equipment

Published on: July 5, 2024

1.9K
Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel10:03

Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel

Published on: October 5, 2018

8.3K

相关概念视频

Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
166
Design Example: Designing a Residential Plumbing System01:25

Design Example: Designing a Residential Plumbing System

The design of residential plumbing systems requires carefully evaluating water demand, flow rates, and pressure dynamics to ensure both efficiency and reliability. The nature of water flow within pipes is defined by its Reynolds number, which classifies flow as either laminar (smooth) or turbulent.
733
Mechanical Characteristics of Steel01:18

Mechanical Characteristics of Steel

The mechanical characteristics of steel are assessed through various tests that evaluate its strength, toughness, and flexibility. These tests include tension, torsion, impact, bending, and hardness assessments, each providing crucial information about steel's suitability for specific applications.
The tension test is fundamental for determining tensile strength. In this test, a steel specimen is stretched using a gripping device until it breaks. The data collected during this test are used...
602
Mechanisms of Heat Transfer I01:14

Mechanisms of Heat Transfer I

Just as interesting as the effects of heat transfer on a system are the methods by which the heat transfer occur. Whenever there is a temperature difference, heat transfer occurs. It may occur rapidly, such as through a cooking pan, or slowly, such as through the walls of a picnic ice box. So many processes involve heat transfer that it is hard to imagine a situation where no heat transfer occurs. Yet, every heat transfer takes place by only three methods: conduction, convection, and radiation.
4.3K
Design Example: Design of an Irrigation Channel01:27

Design Example: Design of an Irrigation Channel

Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
129
Mechanisms of Heat Transfer II01:20

Mechanisms of Heat Transfer II

In convection, thermal energy is carried by the large-scale flow of matter. Ocean currents and large-scale atmospheric circulation, which result from the buoyancy of warm air and water, transfer hot air from the tropics toward the poles and cold air from the poles toward the tropics. The Earth’s rotation interacts with those flows, causing the observed eastward flow of air in the temperate zones. Convection dominates heat transfer by air, and the amount of available space for the airflow...
3.3K