在片重建后安装假肢的挑战和解决方案
Michael E L Leow1, Soumen DAS DE1, Mark E Puhaindran1
1Department of Hand and Reconstructive Microsurgery, National University Hospital, Singapore.
The journal of hand surgery Asian-Pacific volume
|February 1, 2024
概括
假肢装配可以改善复杂的手部重建后的美学和功能. 这项研究详细介绍了挑战指茎的创新修改,实现患者和临床目标.
科学领域:
- 重建性手术是一种重建性手术.
- 假肢的安装 假肢的安装
背景情况:
- 手术重建的目的是恢复长度和功能,但往往会导致形.
- 复杂的重建,特别是带有片和肢体长度保存的复杂重建,可以为假肢创造具有挑战性的茎解剖学.
研究的目的:
- 描述一个具有挑战性的三位数截肢后重建病例的假肢安装策略.
- 详细介绍非传统的假肢修改和技术,以解决带有痕组织的重,长,硬的手指茎.
主要方法:
- 一个患有三位数截肢的病人的案例研究.
- 开发和应用重大,非常规的假肢修改.
- 在假肢安装过程中专注于审美和功能方面的考虑.
主要成果:
- 尽管茎具有复杂的特征,但却取得了成功的假肢安装.
- 在假肢穿戴后,人们注意到了增强的美观外观.
- 观察到手部功能的边际改善.
结论:
- 非传统的假肢修改可以克服适应复杂手部重建后的挑战.
- 假肢配套在改善美学结果和患者满意度方面发挥着至关重要的作用.
- 这种方法满足了患者和临床团队的合适目标.
相关概念视频
00:49Rigid Body Equilibrium Problems - I
A rigid body is said to be in static equilibrium when the net force and the net torque acting on the system is equal to zero. To solve for rigid body equilibrium problems, do the following steps.
01:30Method of Joints: Problem Solving I
The method of joints is a commonly used technique to analyze the forces in structural trusses. The method is based on the principle of equilibrium, which assumes that the truss members are connected by frictionless pins. The forces at each joint can be determined by considering the equilibrium of the forces acting on that joint. Consider a truss structure with two forces of 20 N and 10 N acting at joints C and D, respectively. The method of joints can be used to determine the forces FCB, FDC,...
01:30Method of Joints: Problem Solving II
Consider a truss structure with frictionless joints fixed to a wall and roller support. If a force of 150 N is applied to joint A, the forces in each member of the truss can be determined using the method of joints.
01:24Frames: Problem Solving I
Consider a jib crane with an external load suspended from the pulley. The dimensions of the crane members are shown in the figure. A systematic analysis of the frame structure is required to determine the reaction forces at the pin joints, assuming that the pulleys are frictionless.
01:26Frames: Problem Solving II
Consider a hydraulic hoist supporting a load of 1 kN. Assuming a simplified schematic representation of this frame structure, the force acting on BD and BF members can be determined.
01:14Shearing Stresses in a Beam: Problem Solving
A cantilever beam with a rectangular cross-section under distributed and point loads experiences shearing stresses. The analysis begins by identifying the loads acting on the beam. Then, the reactions at the beam's fixed end are calculated using equilibrium equations. The vertical reaction is a combination of the distributed and point loads, while the moment reaction is the sum of their moments. The shear force distribution along the beam, resulting from these loads, is established by creating...