相关实验视频

Updated: May 5, 2026

A New Murine Model of Endovascular Aortic Aneurysm Repair
08:51

A New Murine Model of Endovascular Aortic Aneurysm Repair

Published on: July 7, 2013

14.4K

在EVAR之后的严重故障模式是特定于设备的

O M Abdul-Malak1, P Cherfan1, N Liang1

  • 1Division of Vascular Surgery, University of Pittsburgh, Pittsburgh, PA, USA.

Journal of endovascular therapy : an official journal of the International Society of Endovascular Specialists
|May 11, 2024
PubMed
概括

内血管动脉瘤修复 (EVAR) 失败,如I型和III型内漏,需要重新干预. 了解设备特定的故障模式对于长期监测和成功的EVAR结果至关重要.

关键词:
埃瓦尔·埃瓦尔 (Evar Evar) 是一个人.动脉瘤是一个动脉瘤.这里是endoleakakak 的位置.

更多相关视频

Time-Resolved, Dynamic Computed Tomography Angiography for Characterization of Aortic Endoleaks and Treatment Guidance via 2D-3D Fusion-Imaging09:32

Time-Resolved, Dynamic Computed Tomography Angiography for Characterization of Aortic Endoleaks and Treatment Guidance via 2D-3D Fusion-Imaging

Published on: December 9, 2021

3.0K
Fully Endoscopic Mitral Valve Repair with Percutaneous Cannulation of Groin Vessels08:12

Fully Endoscopic Mitral Valve Repair with Percutaneous Cannulation of Groin Vessels

Published on: May 26, 2023

1.6K

相关概念视频

Non-ohmic Devices00:51

Non-ohmic Devices

In most substances, the current flow is proportional to the voltage applied to it. A simple relationship between the values of current, voltage, and resistance is known as Ohm's law. Nonohmic devices do not exhibit a linear relationship between voltage and current. One such device is the semiconducting circuit element known as a diode. A diode is a circuit device that allows current flow in only one direction.
Consider a simple circuit consisting of a battery, a diode, and a resistor. A...
1.5K
Types of Errors: Detection and Minimization01:12

Types of Errors: Detection and Minimization

Error is the deviation of the obtained result from the true, expected value or the estimated central value. Errors are expressed in absolute or relative terms.
Absolute error in a measurement is the numerical difference from the true or central value. Relative error is the ratio between absolute error and the true or central value, expressed as a percentage.
Errors can be classified by source, magnitude, and sign. There are three types of errors: systematic, random, and gross.
Systematic or...
8.7K
Design Consideration01:22

Design Consideration

Designing a structure involves a series of considerations, primarily the material's ultimate strength, calculated through tests that measure changes under increased force until the material reaches its breaking point or limit. The ultimate load, where the material breaks, is divided by its original cross-sectional area, resulting in the ultimate normal stress or strength. The ultimate shearing stress is another significant factor taken into account.
The factor of safety is another key...
680
Fatigue01:21

Fatigue

Fatigue occurs when materials rupture under repeated or fluctuating loads, even at stress levels far below their static breaking strength. It typically results in brittle failure, even for ductile materials. It is a critical consideration in designing machines and structural components subjected to repetitive or varying loads. The nature of these loadings can range from fluctuating loads like unbalanced pump impellers causing vibrations to repeatedly bending a thin steel rod wire back and forth...
1.1K
Yield Criteria for Ductile Materials under Plane Stress01:25

Yield Criteria for Ductile Materials under Plane Stress

In designing structural elements and machine parts using ductile materials, it is crucial to ensure that these components withstand applied stresses without yielding. Yielding is initially determined through a tensile test, which evaluates the material's response to uniaxial stress. However, tensile stress is insufficient when components face biaxial or plane stress conditions This condition requires advanced criteria to predict failure.
The Maximum Shearing Stress Criterion, also known as...
836
Fault Types01:18

Fault Types

When analyzing a single line-to-ground fault from phase A to ground at a three-phase bus, it is important to consider the fault impedance. This impedance is zero for a bolted fault, equal to the arc impedance for an arcing fault, and represents the total fault impedance for a transmission-line insulator flashover. To derive sequence and phase currents, fault conditions are translated from the phase domain to the sequence domain.
For line-to-line faults occurring between phases B and C, the...
601