相关实验视频

Updated: Jun 21, 2025

A Teleoperated Robotic System-Assisted Percutaneous Transiliac-Transsacral Screw Fixation Technique
05:57

A Teleoperated Robotic System-Assisted Percutaneous Transiliac-Transsacral Screw Fixation Technique

Published on: January 6, 2023

2.3K

Incisura触角法用于确定综合体固定的跨综合体轴

Toshinari Mashu1, Satoshi Yamaguchi2, Seiji Kimura1

  • 1Graduate School of Medical and Pharmaceutical Sciences, Chiba University, 1-8-1 Inohana, Chuo-ku, Chiba-shi, Chiba 260-8670, Japan.

Foot and ankle surgery : official journal of the European Society of Foot and Ankle Surgeons
|July 16, 2024
PubMed
概括

光镜切口触角 (IT) 方法准确地估计了用于减少关节综合症的跨综合症 (TS) 轴. 这种方法无论切口的解剖结构如何,都能提供一致的测量,有助于精确的手术固定.

关键词:
脚骨折 脚骨折 在脚骨折关节综合症的发生切割切割的接触方法.体体腹膜扩散 (tibiofibular diastasis) 是一种

更多相关视频

C-arm-Free Simultaneous OLIF51 and Percutaneous Pedicle Screw Fixation in a Single Lateral Position12:25

C-arm-Free Simultaneous OLIF51 and Percutaneous Pedicle Screw Fixation in a Single Lateral Position

Published on: September 16, 2022

3.9K
Treatment of Ankle Osteoarthritis with Total Ankle Replacement Through a Lateral Transfibular Approach09:01

Treatment of Ankle Osteoarthritis with Total Ankle Replacement Through a Lateral Transfibular Approach

Published on: January 24, 2018

11.8K

相关概念视频

Unsymmetric Bending - Angle of Neutral Axis01:15

Unsymmetric Bending - Angle of Neutral Axis

Unsymmetrical bending occurs when a structural member is subjected to bending moments in a plane that does not align with the member's principal axes. This scenario typically arises in beams and other structural components when loads are applied at non-ideal angles, introducing complexities in stress analysis.
When a bending moment is applied at an angle θ concerning the vertical axis of a symmetrical member, it can be resolved into components along the member's principal...
295
Method of Joints: Problem Solving I01:30

Method of Joints: Problem Solving I

The method of joints is a commonly used technique to analyze the forces in structural trusses. The method is based on the principle of equilibrium, which assumes that the truss members are connected by frictionless pins. The forces at each joint can be determined by considering the equilibrium of the forces acting on that joint. Consider a truss structure with two forces of 20 N and 10 N acting at joints C and D, respectively. The method of joints can be used to determine the forces FCB, FDC,...
1.1K
Method of Joints: Problem Solving II01:30

Method of Joints: Problem Solving II

Consider a truss structure with frictionless joints fixed to a wall and roller support. If a force of 150 N is applied to joint A, the forces in each member of the truss can be determined using the method of joints.
561
Adjusting a Traverse01:12

Adjusting a Traverse

In the site survey of a four-sided traverse, internal angles are essential to ensure geometric accuracy. The survey revealed that the sum of the measured internal angles was 359 degrees and 48 minutes, which is 12 minutes less than the expected 360 degrees. This discrepancy signals an error likely arising from measurement inaccuracies during the fieldwork.To rectify this error, the adjustment process involved distributing the 12-minute shortfall equally across the four internal angles. By...
55
Beams with Unsymmetric Loadings01:17

Beams with Unsymmetric Loadings

Analyzing a supported beam under unsymmetrical loadings is essential in structural engineering to understand how beams respond to varied force distributions. This analysis involves calculating the deflection and identifying points where the slope of the beam is zero, which are crucial for ensuring structural stability and functionality.
The first moment-area theorem determines the slope at any point on the beam. This theorem indicates that the change in slope between two points on a beam...
114