由于液体透而导致的逐渐腐蚀造成的HeartMate 3传动线损坏:一个案例报告
Tomo Yoshizumi1, Hideki Ito2, Sachie Terazawa2
1Department of Cardiac Surgery, Nagoya University Graduate School of Medicine, 65 Tsurumai, Showa-Ku, Nagoya, 466-8550, Japan. yoshizumi.tomo.s4@f.mail.nagoya-u.ac.jp.
概括
液体透到HeartMate 3传动线连接器中,导致通信故障,并因腐蚀而更换. 立即断开和干燥湿传动线连接器可以防止未来的HeartMate 3故障.
科学领域:
- 心血管外科心血管外科
- 生物医学工程 生物医学工程
- 医疗器械技术 医疗器械技术
背景情况:
- 心脏Mate 3是一个左心室辅助装置 (LVAD),对终端心力衰竭管理至关重要.
- 驱动线感染和设备故障是长期LVAD支持的重大挑战.
- 液体透到设备连接器中可能导致系统故障和设备故障.
研究的目的:
- 为了调查传动线连接器液体透对HeartMate 3设备功能的影响.
- 为了确定湿度暴露,腐蚀和设备报警之间的相关性.
- 为传动线连接器与湿度相关的问题提出预防性策略.
主要方法:
- 一个HeartMate 3患者的病例报告经历了反复出现的"驱动线通信故障"报警.
- 对设备历史的分析,包括先前的干预和部件更换.
- 检查爆炸装置组件的腐蚀和损坏的证据.
主要成果:
- 一名带有HeartMate 3的患者经历了"驱动电路通信故障"警报,原因是液体透到驱动电路连接器中.
- 尽管立即干燥,但随后发生腐蚀,需要更换模块化电缆和系统控制器.
- 经常出现的警报和完全损坏的通讯电缆导致了的更换,在爆炸的电缆连接器上发现了腐蚀.
结论:
- 液体透到HeartMate 3传动线连接器中可能会导致逐渐腐蚀和设备故障,可能需要更换.
- 建议采用多学科的团队方法来评估和管理传动线连接器的湿度暴露.
- 立即断开和干燥湿传动线连接器可能是预防设备故障和延长设备寿命的关键干预措施.
相关概念视频
01:21Fatigue
176
Fatigue occurs when materials rupture under repeated or fluctuating loads, even at stress levels far below their static breaking strength. It typically results in brittle failure, even for ductile materials. It is a critical consideration in designing machines and structural components subjected to repetitive or varying loads. The nature of these loadings can range from fluctuating loads like unbalanced pump impellers causing vibrations to repeatedly bending a thin steel rod wire back and forth...
176
02:49Corrosion
23.9K
The degradation of metals due to natural electrochemical processes is known as corrosion. Rust formation on iron, tarnishing of silver, and the blue-green patina that develops on copper are examples of corrosion. Corrosion involves the oxidation of metals. Sometimes it is protective, such as the oxidation of copper or aluminum, wherein a protective layer of metal oxide or its derivatives forms on the surface, protecting the underlying metal from further oxidation. In other cases, corrosion is...
23.9K
01:09Transmission Shafts: Problem Solving
218
Designing a solid shaft that transmits power from a motor to a machine tool involves a series of calculations to ensure the shaft can withstand the stresses applied by bending moments and torques. First, calculate the torque exerted on the gear, considering the power transmitted by the shaft and its rotational speed. Following this, compute the tangential forces acting on the gears, which directly relate to the torque and the gear radius.
Next, use bending moment diagrams for the shaft to...
Next, use bending moment diagrams for the shaft to...
218
01:15Design of Transmission Shafts - Stress Analysis
332
Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
332
01:10Residual Stresses in Circular Shafts
165
In materials that exhibit elastic and plastic behavior, known as elastoplastic materials, residual stresses can accumulate when these materials experience plastic deformation. This deformation arises from either high levels of shearing stress or significant strains. Residual stresses are internal stresses that persist within a material after removing the external force causing deformation. This phenomenon is demonstrated when observing the behavior of a shaft under torque; notably, the...
165
01:20Plastic Deformation in Circular Shafts
182
When materials are subjected to forces that surpass their yield strength, they undergo a process known as plastic deformation. This results in a permanent alteration or strain in their structure. This concept can be specifically applied to circular shafts, where the deformation leads to a change in its shape. The precise evaluation of this plastic deformation requires understanding the stress distribution within the circular shaft, which is achieved by calculating the maximum shearing stress in...
182