相关实验视频

Updated: Jun 8, 2025

All-electronic Nanosecond-resolved Scanning Tunneling Microscopy: Facilitating the Investigation of Single Dopant Charge Dynamics
11:33

All-electronic Nanosecond-resolved Scanning Tunneling Microscopy: Facilitating the Investigation of Single Dopant Charge Dynamics

Published on: January 19, 2018

9.5K

0.5V,低功率批量驱动的电流差分传导功率放大器

Montree Kumngern1, Fabian Khateb2,3, Tomasz Kulej4

  • 1Department of Telecommunications Engineering, School of Engineering, King Mongkut's Institute of Technology Ladkrabang, Bangkok 10520, Thailand.

Sensors (Basel, Switzerland)
|November 9, 2024
PubMed
概括

这项研究介绍了一种新型的低功耗,低电压电流差分传导放大器 (CDTA),采用散装驱动的MOS晶体管 (BD-MOST) 技术. 这种创新的CDTA可实现多功能电流模式通用过器,可独立控制频率和质量因子.

关键词:
活跃过器是一个活跃过器.大量驱动的 MOS 晶体管.当前差分传导放大器的传导功率放大器.电流模式电路的电路.低压低功率电路的低电压电路.

更多相关视频

Sensing of Barrier Tissue Disruption with an Organic Electrochemical Transistor11:17

Sensing of Barrier Tissue Disruption with an Organic Electrochemical Transistor

Published on: February 10, 2014

11.7K
Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping14:58

Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping

Published on: June 3, 2015

14.5K

相关概念视频

Small-Signal Analysis of MOSFET Amplifiers01:23

Small-Signal Analysis of MOSFET Amplifiers

In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
510
MOSFET Amplifiers01:17

MOSFET Amplifiers

The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
147
Small-Signal Analysis of BJT Amplifiers01:21

Small-Signal Analysis of BJT Amplifiers

Small signal analysis is a fundamental approach used in electronics to understand how a Bipolar Junction Transistor (BJT) amplifier processes signals. In the active region, the BJT is designed for linear amplification. The transistor's behavior under these conditions is governed by its instantaneous base-emitter voltage VBE, a sum of the DC bias VBE, and a small AC signal VBE, resulting in the collector current iC. Here, the collector current has a DC component and an AC component.
984
Biasing of FET01:22

Biasing of FET

Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the...
218
BJT Amplifiers01:14

BJT Amplifiers

Bipolar Junction Transistors (BJTs) are pivotal components in amplifier circuits, functioning as voltage-controlled current sources in their active region. This characteristic allows them to efficiently control the collector current through variations in the base-emitter voltage. Essentially, BJTs amplify power due to their ability to take a weak input signal and output a much stronger signal.
In BJT amplifier configurations, particularly in common-emitter setups, the transistor's role...
407
Biasing of Metal-Semiconductor Junctions01:27

Biasing of Metal-Semiconductor Junctions

Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
215